Intel Arc Pro A30M vs NVIDIA GeForce GTX 1060 5 GB Comparison

Intel
GPU

Intel Arc Pro A30M

CORE STATE DG2-128
VRAM 4 GB
CLOCK SPEED 2000 MHz
TDP 50 W
BUS WIDTH 64 bit
ARCHITECTURE Xe-HPG
nm
PROCESS 6 nm
LAUNCH DATE 2022
VS
NVIDIA
GEFORCE

GeForce GTX 1060 5 GB

CORE STATE GP106
VRAM 5 GB
CLOCK SPEED 1709 MHz
TDP 120 W
BUS WIDTH 160 bit
ARCHITECTURE Pascal
nm
PROCESS 16 nm
LAUNCH DATE 2017

PERFORMANCE BENCHMARKS

geekbench_opencl
31,894
33,397
geekbench_vulkan
N/A
33,991

Analysis: Intel Arc Pro A30M vs NVIDIA GeForce GTX 1060 5 GB

# NVIDIA GeForce GTX 1060 5 GB vs Intel Arc Pro A30M

The benchmark data presents a single direct comparison, and the NVIDIA GeForce GTX 1060 5 GB takes it with a 4.7% lead in Geekbench OpenCL. Yet these two GPUs are radically different creatures—one is a desktop veteran from 2017, the other a mobile professional card from 2022. The scores are close, but the architectures, memory subsystems, and intended workloads tell a more nuanced story. This analysis digs into what each card actually does best, where they diverge, and what the numbers imply for real-world use.

Where Each One Wins

The only head-to-head test available is Geekbench OpenCL, and the GTX 1060 5 GB wins it with a score of 33,397 against the Arc Pro A30M's 31,894. That is a 4.7% advantage—a meaningful but not overwhelming margin. If the workload is compute-heavy and OpenCL-based, the NVIDIA card has the edge in this single measurement.

However, the Arc Pro A30M counters with architectural features that the GTX 1060 cannot match, particularly in ray tracing. The Intel card has 8 dedicated RT cores, while the NVIDIA card has none. For any application that leverages DirectX 12 Ultimate features—which the Arc Pro A30M supports at the 12_2 level—the Intel card is the only one of the two that qualifies. The GTX 1060 stops at DirectX 12 (12_1), meaning it lacks the hardware for variable rate shading, mesh shaders, and other modern rendering paths.

The data also reveals a different kind of win for Intel: efficiency. The Arc Pro A30M is rated at 50 W TDP, less than half of the GTX 1060's 120 W. The Intel card also uses GDDR6 memory with 16 Gbps effective speed, while the NVIDIA card uses GDDR5 at 8 Gbps. For thermally constrained environments or battery-powered mobile workstations, the Arc Pro A30M is the clear winner on paper, even if the benchmark score is lower.

Architecture Differences

The GTX 1060 5 GB is built on NVIDIA's Pascal architecture, using the GP106 chip manufactured on a 16 nm process at TSMC. It packs 4,400 million transistors into a 200 mm² die, yielding a transistor density of 22.0M per mm². The Arc Pro A30M, by contrast, uses Intel's Xe-HPG architecture with the DG2-128 chip on a 6 nm process, also from TSMC. It crams 7,200 million transistors into a smaller 157 mm² die, achieving a much higher density of 45.9M per mm². That is over twice the transistor density, reflecting the newer manufacturing node.

The memory systems diverge sharply. The GTX 1060 has 5 GB of GDDR5 on a 160-bit bus, delivering 160.2 GB/s of bandwidth. The Arc Pro A30M has only 4 GB of GDDR6 on a 64-bit bus, resulting in 128.0 GB/s of bandwidth—20% less. Despite having faster memory technology, Intel's narrow bus limits the throughput. The GTX 1060 also has more shading units (1280 vs 1024), more texture mapping units (80 vs 64), and more ROPs (40 vs 32).

Clock speeds tell a partial counter-story. The GTX 1060 has a base clock of 1506 MHz and boost of 1709 MHz, while the Arc Pro A30M runs at 1500 MHz base and 2000 MHz boost. The Intel card's higher boost clock helps it close the gap in raw compute: its FP32 throughput is 4.096 TFLOPS versus 4.375 TFLOPS for NVIDIA. The gap is only 6.4%, but the Intel card achieves that with 20% fewer shaders, thanks to the higher clock.

The Verdict

For compute workloads measured by OpenCL, the GTX 1060 5 GB is the faster card. Its 4.7% lead in the head-to-head benchmark is backed by higher memory bandwidth and more shading units. If the task is GPU-accelerated rendering, data processing, or any OpenCL-heavy application, the data suggests the NVIDIA card will deliver slightly better performance.

The Arc Pro A30M wins on features and efficiency. It alone supports ray tracing, DirectX 12 Ultimate, and modern rendering pipelines. It consumes 50 W versus 120 W, making it viable in slim laptops or compact professional systems. Its PCIe 4.0 x8 interface doubles the lane bandwidth over the GTX 1060's PCIe 3.0 x16, which can matter for data transfer in certain professional workflows.

Who should pick which? If you need raw OpenCL compute and have desktop power budget, the GTX 1060 5 GB is the data-backed choice. If you need modern graphics features, mobile form factor, or efficiency, the Arc Pro A30M is the only option that satisfies those constraints. The benchmark gap is small; the architectural gap is not.

FAQ

Q: Which GPU has the higher average benchmark score?

A: The NVIDIA GeForce GTX 1060 5 GB has an average benchmark score of 33,694 across its two tests (Geekbench OpenCL at 33,397 and Geekbench Vulkan at 33,991). The Intel Arc Pro A30M has an average score of 31,894 from its single Geekbench OpenCL test.

Q: Does the Intel Arc Pro A30M support ray tracing?

A: Yes. The Arc Pro A30M has 8 dedicated ray tracing cores, while the NVIDIA GeForce GTX 1060 5 GB has none. The Intel card also supports DirectX 12 Ultimate (12_2), whereas the GTX 1060 is limited to DirectX 12 (12_1).

Q: How much faster is the GTX 1060 in the head-to-head OpenCL test?

A: The GTX 1060 scores 33,397 versus 31,894 for the Arc Pro A30M, a delta of 4.7%. This is the only benchmark where both cards were tested under the same conditions.

Q: What is the memory bandwidth difference?

A: The GTX 1060 5 GB has 160.2 GB/s of bandwidth from GDDR5 on a 160-bit bus. The Arc Pro A30M has 128.0 GB/s from GDDR6 on a 64-bit bus. That is a 25% advantage for the NVIDIA card in raw bandwidth.

Q: Which card is more power-efficient?

A: The Intel Arc Pro A30M is rated at 50 W TDP, compared to 120 W for the GTX 1060. The Intel card achieves 95.4% of the GTX 1060's FP32 throughput (4.096 vs 4.375 TFLOPS) while drawing less than half the power.

Q: What is the transistor density comparison?

A: The Arc Pro A30M packs 7,200 million transistors into 157 mm², for a density of 45.9M per mm². The GTX 1060 has 4,400 million transistors on 200 mm², yielding 22.0M per mm². The Intel card's density is more than double due to its 6 nm process versus 16 nm.

Head-to-Head Benchmarks

The single head-to-head result is Geekbench OpenCL, and it tells a clear story: NVIDIA wins with 33,397 points, beating Intel's 31,894 by 4.7%. This margin is modest but consistent with the specification differences. The GTX 1060 has 25% more memory bandwidth (160.2 GB/s vs 128.0 GB/s) and 25% more shading units (1280 vs 1024). However, the Arc Pro A30M closes the compute gap through its higher boost clock of 2000 MHz versus 1709 MHz, achieving FP32 throughput within 6.4% of the NVIDIA card.

The fact that the GTX 1060 wins by only 4.7% despite its bandwidth and shader advantages suggests the Intel card's architecture is more efficient per compute unit. The Arc Pro A30M's FP16 performance of 8.192 TFLOPS (2:1 ratio) dwarfs the GTX 1060's 68.36 GFLOPS (1:64 ratio), indicating the Intel card is far better suited for workloads that can use reduced precision. The NVIDIA card's FP16 performance is negligible by comparison.

Another notable difference is the memory clock. The GTX 1060 runs its GDDR5 at 2002 MHz (8 Gbps effective), while the Arc Pro A30M runs GDDR6 at 2000 MHz (16 Gbps effective). The Intel memory is twice as fast per pin, but the 64-bit bus halves that advantage, resulting in the 128.0 GB/s figure. This suggests Intel optimized for power efficiency over raw bandwidth, a reasonable trade for a 50 W mobile part.

Specification Differences

| Specification | NVIDIA GeForce GTX 1060 5 GB | Intel Arc Pro A30M |

|---|---|---|

| Architecture | Pascal | Xe-HPG |

| Process Node | 16 nm | 6 nm |

| Transistors | 4,400 million | 7,200 million |

| Die Size | 200 mm² | 157 mm² |

| Transistor Density | 22.0M / mm² | 45.9M / mm² |

| Base Clock | 1506 MHz | 1500 MHz |

| Boost Clock | 1709 MHz | 2000 MHz |

| Memory Size | 5 GB | 4 GB |

| Memory Type | GDDR5 | GDDR6 |

| Memory Bus | 160 bit | 64 bit |

| Memory Bandwidth | 160.2 GB/s | 128.0 GB/s |

| Memory Speed | 8 Gbps effective | 16 Gbps effective |

| Shading Units | 1280 | 1024 |

| TMUs | 80 | 64 |

| ROPs | 40 | 32 |

| RT Cores | None | 8 |

| FP32 | 4.375 TFLOPS | 4.096 TFLOPS |

| FP16 | 68.36 GFLOPS (1:64) | 8.192 TFLOPS (2:1) |

| TDP | 120 W | 50 W |

| Power Connectors | 1x 6-pin | None |

| Bus Interface | PCIe 3.0 x16 | PCIe 4.0 x8 |

| DirectX | 12 (12_1) | 12 Ultimate (12_2) |

| Display Outputs | 1x DVI, 1x HDMI 2.0, 3x DisplayPort 1.4a | Portable Device Dependent |

The two cards are separated by five years of GPU evolution. The GTX 1060 is a dual-slot desktop card with a 250 mm length, while the Arc Pro A30M is a mobile part with no specified dimensions. The NVIDIA card uses a 6-pin power connector and recommends a 300 W PSU; the Intel card needs no external power at all. The GTX 1060 is end-of-life, as is the Arc Pro A30M, but they served entirely different markets. One is a legacy desktop workhorse; the other is a professional mobile solution with modern features. The data shows they are close in OpenCL compute, but the specifications reveal two fundamentally different design philosophies.

DETAILED SPECIFICATIONS

SPECIFICATION
Pro A30M
GTX 1060 5 GB
Core Specs
Shading Units
1,024
1,280 +25.0%
Shaders
1,024
1,280 +25.0%
TMUs
64
80 +25.0%
ROPs
32
40 +25.0%
SM Count
—
10
Execution Units
128
—
Clocks
Base Clock
1500 MHz
1506 MHz
Boost Clock
2000 MHz
1709 MHz
Memory Clock
2000 MHz 16 Gbps effective
2002 MHz 8 Gbps effective
Memory
Memory Size
4 GB
5 GB
VRAM (MB)
4,096
5,120 +25.0%
Memory Type
GDDR6
GDDR5
Memory Bus
64 bit
160 bit
Bandwidth
128.0 GB/s
160.2 GB/s
Cache
L1 Cache
—
48 KB (per SM)
L2 Cache
4 MB
1280 KB
Performance
Pixel Rate
64.00 GPixel/s
68.36 GPixel/s
Texture Rate
128.0 GTexel/s
136.7 GTexel/s
FP32 (TFLOPS)
4.096 TFLOPS
4.375 TFLOPS
FP64 (TFLOPS)
1,024.0 GFLOPS (1:4)
136.7 GFLOPS (1:32)
FP16 (TFLOPS)
8.192 TFLOPS (2:1)
68.36 GFLOPS (1:64)
AI/RT
RT Cores
8
—
XMX Cores
128
—
Power
TDP
50 W
120 W
TDP (W)
50
120 +140.0%
Suggested PSU
—
300 W
Power Connectors
None
1x 6-pin
Architecture
Architecture
Xe-HPG
Pascal
GPU Name
DG2-128
GP106
Generation
Alchemist (Pro-Series Mobile)
GeForce 10
Process Size
6 nm
16 nm
Transistors
7,200 million
4,400 million
Die Size
157 mm²
200 mm²
Foundry
TSMC
TSMC
Density
45.9M / mm²
22.0M / mm²
API Support
DirectX
12 Ultimate (12_2)
12 (12_1)
OpenGL
4.6
4.6
Vulkan
1.4
1.4
OpenCL
3.0
3.0
CUDA
—
6.1
Shader Model
6.6
6.8
Physical
Slot Width
—
Dual-slot
Length
—
250 mm 9.8 inches
Outputs
Portable Device Dependent
1x DVI1x HDMI 2.03x DisplayPort 1.4a
Bus Interface
PCIe 4.0 x8
PCIe 3.0 x16
Other
Production
End-of-life
End-of-life
Predecessor
—
GeForce 900
Successor
—
GeForce 20
View Arc Pro A30M Details View GeForce GTX 1060 5 GB Details