AMD Radeon RX 9060 XT 16 GB vs Intel HD Graphics P530 Comparison
AMD Radeon RX 9060 XT 16 GB
HD Graphics P530
PERFORMANCE BENCHMARKS
Analysis: AMD Radeon RX 9060 XT 16 GB vs Intel HD Graphics P530
The AMD Radeon RX 9060 XT 16 GB and Intel HD Graphics P530 occupy opposite ends of the hardware spectrum, yet their aggregate benchmark scores place them within 1% of each other. The RX 9060 XT averages 4657 points against the P530’s 4560, a difference of roughly 2.1%. However, this near-parity in average score masks extreme divergence in individual workloads, architectural capability, and system role. The data shows a discrete, current-generation RDNA 4.0 part facing an integrated, end-of-life Skylake GPU.
Head-to-Head Benchmarks
The two GPUs share no common benchmark entries in the FACT PACK, so a direct per-test comparison is impossible. Instead, the data must be interpreted through each card’s own benchmark suite and its nearest rivals.
The RX 9060 XT’s strongest results come from synthetic 3D workloads. In 3DMark Steel Nomad (DX12), it scores 4093 points. Its PassMark G3D score is 20099, while its PassMark G2D score is 1169. The compute-oriented PassMark GPU Compute test yields 11234 points. These are substantial figures for a modern GPU. However, its legacy DirectX scores are surprisingly low: PassMark DirectX 9 returns 305, DirectX 11 returns 185, DirectX 10 returns 116, and DirectX 12 returns 57. This pattern suggests the card is heavily optimized for modern APIs and asynchronous compute, with older fixed-function paths performing poorly relative to its raw shader throughput.
The Intel HD Graphics P530 only has two benchmark results: Geekbench OpenCL at 4549 and Geekbench Vulkan at 4571. These scores are nearly identical, differing by less than 0.5%. This consistency indicates a balanced compute and graphics design, but the absolute numbers are far below the RX 9060 XT’s peak results. The P530’s 384.0 GFLOPS FP32 throughput is dwarfed by the RX 9060 XT’s 25.64 TFLOPS — a 66.7x difference. In pixel rate, the RX 9060 XT outputs 200.3 GPixel/s versus the P530’s 3.000 GPixel/s. Texture rate shows a similar gap: 400.6 GTexel/s versus 16.00 GTexel/s.
Looking at nearest rivals clarifies the picture. The RX 9060 XT’s closest competitor by average score is the AMD Radeon R5 M320 at a 0% delta. The NVIDIA Quadro P400 is 0.6% slower, the GeForce GTX 970M is 0.6% faster, and the Quadro M3000M is 0.8% faster. This places the RX 9060 XT in a strange position: its average score is comparable to mid-2010s mobile GPUs, yet its individual benchmark peaks (G3D 20099, compute 11234) are far beyond anything those older parts could achieve. The low DirectX scores drag its average down disproportionately.
The P530’s rivals show a different cluster. The AMD Radeon RX 560 is 0.2% faster, the Radeon R5 M230 is 0.4% faster, the FirePro W4190M is 1.2% slower, and the Quadro M3000M is 1.3% faster. Notably, the Quadro M3000M appears in both cards’ rival lists — it is 0.8% faster than the RX 9060 XT and 1.3% faster than the P530. This overlapping rival suggests that, despite the generational chasm, both cards occupy a similar tier in aggregate benchmark rankings.
The Verdict
Data dictates a clear split: the RX 9060 XT is for anyone needing modern API support, high-resolution texturing, and heavy compute. Its 16 GB GDDR6 memory with 322.3 GB/s bandwidth is a fundamental advantage. The P530 uses system-shared memory with system-dependent bandwidth, which cannot sustain the same data throughput. The RX 9060 XT’s 2048 shading units versus 192, its 128 TMUs versus 16, and its 64 ROPs versus 3 are categorical wins.
The P530’s only logical pick is for legacy systems or ultra-low-power builds. Its 15 W TDP versus 160 W makes it suitable for fanless or battery-constrained designs. It supports DirectX 12 (12_1), OpenGL 4.6, and Vulkan 1.3, so it can run modern APIs at minimal settings. However, its 3 ROPs are a severe bottleneck; the RX 9060 XT has 21.3x the pixel throughput.
For gaming, the RX 9060 XT’s 32 RT cores and 12 Ultimate (12_2) API support provide hardware ray tracing and mesh shaders, features entirely absent from the P530. For compute, the RX 9060 XT’s FP16 at 1:1 ratio (25.64 TFLOPS) is a notable advantage over the P530’s 2:1 ratio (768.0 GFLOPS). The RX 9060 XT also has a 4 nm process node against 14 nm+, a 199 mm² die against 123 mm², and 29,700 million transistors (the P530’s transistor count is not listed).
The P530 is end-of-life, while the RX 9060 XT is active. The RX 9060 XT released on 2025-06-03, roughly a decade after the P530’s 2015-08-31 launch. No professional workload in the data favors the P530. The verdict is unambiguous: the RX 9060 XT wins every meaningful performance category, while the P530 retains a niche only for its 15 W power envelope and integrated simplicity.
Architecture Differences
The architectural gap is generational. The RX 9060 XT uses RDNA 4.0 on a 4 nm TSMC process, with the Navi 44 chip under the Strix Point codename. It belongs to the Navi IV (RX 9000) generation. The P530 uses Generation 9.0 architecture on Intel’s 14 nm+ process, with the Skylake GT2 chip in the HD Graphics-W (Skylake) generation.
The RX 9060 XT has a dedicated 128-bit memory bus with 16 GB of GDDR6, delivering 322.3 GB/s. The P530 has no dedicated memory; it uses system-shared memory with a system-dependent bus width and bandwidth. This is the most consequential architectural difference for real-world performance.
Compute features differ sharply. The RX 9060 XT has 32 ray tracing cores; the P530 has none. The RX 9060 XT’s FP16 throughput equals its FP32 at 25.64 TFLOPS (1:1 ratio), while the P530’s FP16 is 768.0 GFLOPS at a 2:1 ratio. The RX 9060 XT supports DirectX 12 Ultimate (12_2), Vulkan 1.4, and OpenGL 4.6. The P530 supports DirectX 12 (12_1), Vulkan 1.3, and OpenGL 4.6 — one API version behind in each case.
The RX 9060 XT connects via PCIe 5.0 x16, a high-bandwidth external interface. The P530 uses a Ring Bus, tying it directly to the CPU’s interconnect. The RX 9060 XT has a dual-slot cooler with a single 8-pin power connector and requires a 450 W suggested PSU. The P530 is an IGP (integrated graphics processor) with no power connectors or PSU requirement. The RX 9060 XT outputs 1x HDMI 2.1b and 2x DisplayPort 2.1a; the P530’s outputs are motherboard-dependent.
Die size and transistor density also differ. The RX 9060 XT has a 199 mm² die with 29,700 million transistors, yielding a density of 149.2M per mm². The P530 has a 123 mm² die, but its transistor count and density are not listed. The RX 9060 XT’s production status is Active; the P530 is End-of-life.
Specification Differences
| Specification | AMD Radeon RX 9060 XT 16 GB | Intel HD Graphics P530 |
|---|---|---|
| Process Node | 4 nm | 14 nm+ |
| Die Size | 199 mm² | 123 mm² |
| Base Clock | 1700 MHz | 350 MHz |
| Boost Clock | 3130 MHz | 1000 MHz |
| Memory Size | 16 GB GDDR6 | System Shared |
| Memory Bus | 128 bit | System Shared |
| Memory Bandwidth | 322.3 GB/s | System Dependent |
| Shading Units | 2048 | 192 |
| TMUs | 128 | 16 |
| ROPs | 64 | 3 |
| RT Cores | 32 | None |
| Pixel Rate | 200.3 GPixel/s | 3.000 GPixel/s |
| Texture Rate | 400.6 GTexel/s | 16.00 GTexel/s |
| FP32 | 25.64 TFLOPS | 384.0 GFLOPS |
| FP16 | 25.64 TFLOPS (1:1) | 768.0 GFLOPS (2:1) |
| TDP | 160 W | 15 W |
| Bus Interface | PCIe 5.0 x16 | Ring Bus |
| DirectX | 12 Ultimate (12_2) | 12 (12_1) |
| Vulkan | 1.4 | 1.3 |
| Production Status | Active | End-of-life |
The RX 9060 XT also has a game clock of 2530 MHz and a memory clock of 2518 MHz (20.1 Gbps effective), neither of which the P530 lists. The P530’s base clock of 350 MHz and boost of 1000 MHz are dramatically lower than the RX 9060 XT’s 1700 MHz base and 3130 MHz boost. The RX 9060 XT’s launch MSRP is 349 USD. The P530 has no launch MSRP listed.
FAQ
Q: Why do the two GPUs have nearly identical average benchmark scores despite massive spec differences?
A: The RX 9060 XT’s average score of 4657 is dragged down by very low legacy DirectX scores (PassMark DirectX 12: 57, DirectX 11: 185, DirectX 10: 116). The P530’s average of 4560 comes from only two Geekbench tests (OpenCL: 4549, Vulkan: 4571), which are moderately consistent. The averages are coincidental, not indicative of equal performance.
Q: Which card has higher raw compute throughput?
A: The RX 9060 XT has 25.64 TFLOPS FP32, which is 66.7 times the P530’s 384.0 GFLOPS. The RX 9060 XT also matches FP16 at 25.64 TFLOPS (1:1), while the P530’s FP16 is 768.0 GFLOPS (2:1).
Q: Can the Intel HD Graphics P530 run modern games?
A: It supports DirectX 12 (12_1), OpenGL 4.6, and Vulkan 1.3, so it can launch modern API titles. However, its 3 ROPs and 3.000 GPixel/s pixel rate severely limit resolution and detail settings. It has no ray tracing cores.
Q: What is the memory configuration difference?
A: The RX 9060 XT has 16 GB of dedicated GDDR6 on a 128-bit bus with 322.3 GB/s bandwidth. The P530 uses system-shared memory with a system-dependent bus width and bandwidth, sharing the system’s RAM and memory controller.
Q: Does the RX 9060 XT support hardware ray tracing?
A: Yes, it has 32 dedicated ray tracing cores and supports DirectX 12 Ultimate (12_2), which includes DirectX Raytracing. The P530 has no RT cores and only supports DirectX 12 (12_1).
Q: Which card has better API support?
A: The RX 9060 XT supports DirectX 12 Ultimate (12_2), Vulkan 1.4, and OpenGL 4.6. The P530 supports DirectX 12 (12_1), Vulkan 1.3, and OpenGL 4.6. The RX 9060 XT is one API version ahead in both DirectX and Vulkan.