NVIDIA Quadro K5100M vs NVIDIA RTX PRO 6000 Blackwell Max-Q Comparison

NVIDIA
GEFORCE

NVIDIA Quadro K5100M

CORE STATE GK104
VRAM 8 GB
CLOCK SPEED 771 MHz
TDP 100 W
BUS WIDTH 256 bit
ARCHITECTURE Kepler
nm
PROCESS 28 nm
LAUNCH DATE 2013
VS
NVIDIA
GEFORCE

RTX PRO 6000 Blackwell Max-Q

CORE STATE GB202
VRAM 96 GB
CLOCK SPEED 2280 MHz
TDP 300 W
BUS WIDTH 512 bit
ARCHITECTURE Blackwell 2.0
nm
PROCESS 5 nm
LAUNCH DATE 2025

PERFORMANCE BENCHMARKS

geekbench_metal
8,315
N/A
geekbench_opencl
11,771
N/A
3dmark_3dmark_steel_nomad_dx12
N/A
11,088

Analysis: NVIDIA Quadro K5100M vs NVIDIA RTX PRO 6000 Blackwell Max-Q

NVIDIA's RTX PRO 6000 Blackwell Max-Q and Quadro K5100M sit at opposite ends of the professional GPU timeline, and the benchmark data reflects a generational chasm. The RTX PRO 6000 Blackwell Max-Q achieves an average benchmark score of 11,088, placing it in the 50th percentile of all GPUs, while the Quadro K5100M averages 10,043, landing in the 48th percentile. These aggregate scores, however, obscure the fact that the two cards were measured on entirely different test suites, so direct numerical comparison is less meaningful than understanding each card's standing among its own contemporaries.

Head-to-Head Benchmarks

The FACT PACK provides no shared benchmark results between these two cards, so a direct apples-to-apples comparison is impossible. Instead, the data shows each card's performance through different lenses. The RTX PRO 6000 Blackwell Max-Q posts a single 3DMark Steel Nomad DX12 score of 11,088. That result places it exactly tied with the NVIDIA RTX PRO 6000D Blackwell Max-Q, which also scores 11,088 (0% delta). It edges out the AMD Radeon RX 550 by 0.1% (11,088 vs. 11,075) and the NVIDIA GeForce GTX 1650 SUPER by 0.4% (11,088 vs. 11,047). Interestingly, the AMD FirePro W4300 scores higher at 11,225, giving it a 1.2% advantage over the RTX PRO 6000 in this specific test. This suggests that the RTX PRO 6000's raw DX12 throughput is competitive with, but not dominant over, a handful of far less expensive consumer and workstation cards.

The Quadro K5100M's performance is charted through Geekbench compute tests. It scores 8,315 in Geekbench Metal and 11,771 in Geekbench OpenCL, averaging to 10,043. Against its nearest rivals, the K5100M sits slightly below the AMD Radeon R9 M375 (10,070, which is 0.3% higher) and above the AMD Radeon Pro 5300M (10,013, which is 0.3% lower). It also beats the NVIDIA GeForce GTX 870M (9,959) by 0.8% and the NVIDIA Quadro 6000 (9,846) by 2%. The K5100M's OpenCL result of 11,771 is notably strong, exceeding its own Metal score by over 3,400 points, indicating that its compute performance varies significantly depending on the API. In contrast, the RTX PRO 6000's single benchmark result gives no indication of cross-API variance, though its architecture supports DirectX 12 Ultimate, OpenGL 4.6, and Vulkan 1.4.

The biggest win for the RTX PRO 6000 is the sheer scale of its compute resources: 24,064 shading units, 752 TMUs, and 192 ROPs, producing 109.7 TFLOPS of FP32 performance. The K5100M offers 1,536 shading units, 128 TMUs, and 32 ROPs, yielding 2.369 TFLOPS FP32. That is a 46-fold difference in theoretical FP32 throughput. The K5100M's strongest showing is its OpenCL score relative to its own hardware class; it outperforms the Quadro 6000 by 2%, a card from the same era. The RTX PRO 6000's strongest showing is its perfect tie with the RTX PRO 6000D, confirming that the Max-Q variant loses no performance to its non-Max-Q sibling in this benchmark.

FAQ

Q: How does the RTX PRO 6000 Blackwell Max-Q compare to its closest rival, the RTX PRO 6000D?

A: The two cards are benchmark twins. Both score exactly 11,088 in 3DMark Steel Nomad DX12, resulting in a 0% delta. The data shows no performance difference between them in this test.

Q: Is the Quadro K5100M faster than the AMD Radeon Pro 5300M?

A: Yes, but barely. The K5100M averages 10,043, which is 0.3% higher than the Radeon Pro 5300M's 10,013. This is a marginal lead, well within typical run-to-run variance.

Q: What is the RTX PRO 6000's percentile ranking, and what does that mean?

A: It sits in the 50th percentile of all GPUs. This means half of all GPUs in the database score lower, and half score higher. For a top-tier professional card, this percentile reflects that its single benchmark score is moderate, not elite, when compared across all hardware.

Q: Does the Quadro K5100M support ray tracing or tensor cores?

A: No. The FACT PACK lists no RT core count and no tensor core count for the K5100M. The RTX PRO 6000, by contrast, includes 188 RT cores and 752 tensor cores.

Q: Which card has a higher memory bandwidth?

A: The RTX PRO 6000's GDDR7 memory on a 512-bit bus delivers 1.79 TB/s. The K5100M's GDDR5 on a 256-bit bus delivers 115.2 GB/s. The RTX PRO 6000 has over 15 times the bandwidth.

Q: What is the production status of each card?

A: The RTX PRO 6000 Blackwell Max-Q is listed as "Active" production, released on 2025-03-17. The Quadro K5100M is "End-of-life," released on 2013-07-22, with its successor being the Quadro Maxwell-M.

Where Each One Wins

The RTX PRO 6000 Blackwell Max-Q wins decisively in scenarios demanding raw throughput and modern features. Its 109.7 TFLOPS FP32 performance, 1.79 TB/s memory bandwidth, and 96 GB of GDDR7 memory make it suited for large-scale compute tasks, AI workloads, and high-resolution rendering. The presence of 188 RT cores and 752 tensor cores means it is built for ray-traced workflows and machine learning inference. Its PCIe 5.0 x16 interface and support for DirectX 12 Ultimate, Vulkan 1.4, and four DisplayPort 2.1b outputs position it for current-generation professional workstations. The 300 W TDP and 700 W suggested PSU indicate a desktop-oriented card that demands serious power delivery.

The Quadro K5100M wins in portability and legacy compatibility. Its 100 W TDP and MXM Module form factor with no power connectors make it a drop-in solution for older mobile workstations. It supports DirectX 12 (11_0) and Vulkan 1.2.175, which is adequate for older software stacks. Its 8 GB of GDDR5 memory is modest but functional for its era. The K5100M's OpenCL score of 11,771 shows it can still perform respectable compute duties in applications optimized for that API. For a system that requires a specific MXM-B (3.0) form factor, the K5100M is the only choice between these two, as the RTX PRO 6000 is a dual-slot, 267 mm desktop card.

In terms of benchmark percentile, the RTX PRO 6000 at 50th percentile edges out the K5100M at 48th, but both sit near the median of all GPUs. The RTX PRO 6000's advantage is not in percentile rank but in the scale of its capabilities—it has 15.7 times more shading units, 5.9 times more TMUs, and 6 times more ROPs than the K5100M. The K5100M's wins are confined to its mobile form factor and lower power envelope.

Specification Differences

The two cards differ in nearly every measurable specification. The RTX PRO 6000 uses a GB202 chip on a 5 nm TSMC process, with 92,200 million transistors on a 750 mm² die. The K5100M uses a GK104 chip on a 28 nm TSMC process, with 3,540 million transistors on a 294 mm² die. Transistor density is 122.9M per mm² for the RTX PRO 6000 versus 12.0M per mm² for the K5100M. Clock speeds are drastically different: the RTX PRO 6000 runs at 1035 MHz base and 2280 MHz boost, while the K5100M is locked at 771 MHz for both base and boost. Memory configurations are 96 GB GDDR7 on a 512-bit bus vs. 8 GB GDDR5 on a 256-bit bus, yielding 1.79 TB/s vs. 115.2 GB/s bandwidth.

The RTX PRO 6000 has 24,064 shading units, 752 TMUs, 192 ROPs, 188 RT cores, and 752 tensor cores. The K5100M has 1,536 shading units, 128 TMUs, and 32 ROPs, with no RT or tensor cores. Pixel rate is 437.8 GPixel/s vs. 24.67 GPixel/s, and texture rate is 1,714.6 GTexel/s vs. 98.69 GTexel/s. FP32 throughput is 109.7 TFLOPS vs. 2.369 TFLOPS. The RTX PRO 6000 supports FP16 at 109.7 TFLOPS (1:1), while the K5100M lists no FP16 capability. Power draw is 300 W vs. 100 W. The RTX PRO 6000 is dual-slot with a 1x 16-pin connector and requires a 700 W PSU; the K5100M is an MXM Module with no connectors and no suggested PSU. Bus interfaces are PCIe 5.0 x16 vs. MXM-B (3.0). Display outputs are 4x DisplayPort 2.1b vs. portable device dependent.

Architecture Differences

The architectural gap is foundational. The RTX PRO 6000 is built on Blackwell 2.0 architecture, part of the Blackwell PRO W (x000) generation, and is the successor to Workstation Ada. It is manufactured on a 5 nm process at TSMC. The K5100M is built on Kepler architecture, part of the Quadro Kepler-M (Kx100M) generation, succeeding Quadro Fermi-M and preceding Quadro Maxwell-M. It uses a 28 nm process.

The RTX PRO 6000's Blackwell architecture introduces dedicated RT cores and tensor cores, which are absent from the K5100M. This means the RTX PRO 6000 can handle hardware-accelerated ray tracing and AI tensor operations, while the K5100M relies on traditional shader-based compute. The RTX PRO 6000's 92,200 million transistors are packed into a 750 mm² die, representing a 26-fold increase in transistor count over the K5100M's 3,540 million. The 5 nm node allows for a transistor density of 122.9M per mm², over 10 times the density of the 28 nm K5100M.

Memory architecture differs as well: the RTX PRO 6000 uses 28 Gbps effective GDDR7, while the K5100M uses 3.6 Gbps effective GDDR5. The RTX PRO 6000's 512-bit bus is double the K5100M's 256-bit bus. The RTX PRO 6000 also supports a broader API set, including Vulkan 1.4 and DirectX 12 Ultimate, versus the K5100M's Vulkan 1.2.175 and DirectX 12 (11_0). The RTX PRO 6000 has a release date of 2025-03-17, nearly 12 years after the K5100M's 2013-07-22 launch. The K5100M's production status is end-of-life, while the RTX PRO 6000 is active.

The Verdict

The data points to a clear generational verdict: the RTX PRO 6000 Blackwell Max-Q is the only sensible choice for any modern professional workload. Its 109.7 TFLOPS FP32, 96 GB memory, and RT/tensor core support are overwhelming advantages. It matches its closest rival exactly and holds its own against newer consumer cards. Its 300 W TDP is substantial but justified by the performance envelope. The RTX PRO 6000 is for users running current 3D applications, AI inference, or high-resolution video work on a desktop workstation.

The Quadro K5100M is strictly for legacy systems. Its 8 GB memory and 2.369 TFLOPS are insufficient for any contemporary task. Its 48th percentile ranking, while close to the RTX PRO 6000's 50th, is based on older, less demanding benchmarks. The K5100M's only advantages are its 100 W power draw and MXM form factor, which are irrelevant unless you have a specific mobile workstation that requires it. If you are building or upgrading a system today, the RTX PRO 6000 is the data-backed pick. If you are maintaining a 2013-era laptop, the K5100M remains a functional, if dated, option. There is no scenario where the K5100M wins on performance, memory, or features.

DETAILED SPECIFICATIONS

SPECIFICATION
Quadro K5100M
RTX PRO 6000 Blackwell Max-Q
Core Specs
Shading Units
1,536
24,064 +1466.7%
Shaders
1,536
24,064 +1466.7%
TMUs
128
752 +487.5%
ROPs
32
192 +500.0%
SM Count
—
188
Clocks
Base Clock
771 MHz
1035 MHz
Boost Clock
771 MHz
2280 MHz
Memory Clock
900 MHz 3.6 Gbps effective
1750 MHz 28 Gbps effective
Memory
Memory Size
8 GB
96 GB
VRAM (MB)
8,192
98,304 +1100.0%
Memory Type
GDDR5
GDDR7
Memory Bus
256 bit
512 bit
Bandwidth
115.2 GB/s
1.79 TB/s
Cache
L1 Cache
16 KB (per SMX)
128 KB (per SM)
L2 Cache
512 KB
128 MB
Performance
Pixel Rate
24.67 GPixel/s
437.8 GPixel/s
Texture Rate
98.69 GTexel/s
1,714.6 GTexel/s
FP32 (TFLOPS)
2.369 TFLOPS
109.7 TFLOPS
FP64 (TFLOPS)
98.69 GFLOPS (1:24)
1.715 TFLOPS (1:64)
FP16 (TFLOPS)
—
109.7 TFLOPS (1:1)
AI/RT
RT Cores
—
188
Tensor Cores
—
752
Power
TDP
100 W
300 W
TDP (W)
100
300 +200.0%
Suggested PSU
—
700 W
Power Connectors
None
1x 16-pin
Architecture
Architecture
Kepler
Blackwell 2.0
GPU Name
GK104
GB202
Generation
Quadro Kepler-M (Kx100M)
Blackwell PRO W (x000)
Process Size
28 nm
5 nm
Transistors
3,540 million
92,200 million
Die Size
294 mm²
750 mm²
Foundry
TSMC
TSMC
Density
12.0M / mm²
122.9M / mm²
API Support
DirectX
12 (11_0)
12 Ultimate (12_2)
OpenGL
4.6
4.6
Vulkan
1.2.175
1.4
OpenCL
3.0
3.0
CUDA
3.0
12.0
Shader Model
6.5 (5.1)
6.9
Physical
Slot Width
MXM Module
Dual-slot
Length
—
267 mm 10.5 inches
Height
—
111 mm 4.4 inches
Outputs
Portable Device Dependent
4x DisplayPort 2.1b
Bus Interface
MXM-B (3.0)
PCIe 5.0 x16
Other
Launch Price
—
8,565 USD
Production
End-of-life
Active
Predecessor
Quadro Fermi-M
Workstation Ada
Successor
Quadro Maxwell-M
—
View Quadro K5100M Details View RTX PRO 6000 Blackwell Max-Q Details