NVIDIA GeForce GTX 560 SE vs NVIDIA RTX PRO 5000 72 GB Blackwell Comparison

NVIDIA
GEFORCE

NVIDIA GeForce GTX 560 SE

CORE STATE GF114
VRAM 1024 MB
CLOCK SPEED —
TDP 150 W
BUS WIDTH 192 bit
ARCHITECTURE Fermi 2.0
nm
PROCESS 40 nm
LAUNCH DATE 2012
VS
NVIDIA
GEFORCE

RTX PRO 5000 72 GB Blackwell

CORE STATE GB202
VRAM 72 GB
CLOCK SPEED 2377 MHz
TDP 300 W
BUS WIDTH 384 bit
ARCHITECTURE Blackwell 2.0
nm
PROCESS 5 nm
LAUNCH DATE 2025

PERFORMANCE BENCHMARKS

geekbench_opencl
7,171
N/A
3dmark_3dmark_steel_nomad_dx12
N/A
9,579.5
passmark_directx_10
N/A
175
passmark_directx_11
N/A
219
passmark_directx_12
N/A
78
passmark_directx_9
N/A
311
passmark_g2d
N/A
914
passmark_g3d
N/A
24,310
passmark_gpu_compute
N/A
15,667

Analysis: NVIDIA GeForce GTX 560 SE vs NVIDIA RTX PRO 5000 72 GB Blackwell

Head-to-Head Benchmarks

The benchmark database contains no direct head-to-head tests between the NVIDIA GeForce GTX 560 SE and the NVIDIA RTX PRO 5000 72 GB Blackwell. Instead, each card has its own distinct benchmark portfolio, making cross-comparison indirect. The GTX 560 SE has a single Geekbench OpenCL score of 7,171. The RTX PRO 5000 has a broader set of Passmark and 3DMark results, with a Passmark G3D score of 24,310, a Passmark GPU Compute score of 15,667, and a 3DMark Steel Nomad DX12 score of 9,579.5. These are not overlapping tests, so the data cannot be used to declare a single winner across identical workloads.

What the data does show is that the RTX PRO 5000’s Passmark G3D result is roughly 3.4 times higher than the GTX 560 SE’s Geekbench OpenCL score, but again, these are different benchmarks measuring different APIs and workloads. The RTX PRO 5000’s DirectX 12 Passmark score of 78 is surprisingly low compared to its DirectX 11 score of 219 and DirectX 9 score of 311. This suggests that the RTX PRO 5000’s performance profile is heavily workload-dependent, with legacy DirectX 9 and 11 titles showing relatively stronger results than DirectX 12 in this particular Passmark test. The GTX 560 SE, by contrast, only reports a single OpenCL figure, leaving its DirectX legacy performance undocumented in this database.

The nearest rivals for each card further illustrate their different market positions. The GTX 560 SE sits within a tight cluster: it is essentially tied with the Intel Iris Pro Graphics P580 (7,170, delta 0%), the NVIDIA GeForce GTX 970 (7,157, delta 0.2%), the AMD Radeon Vega 8 Mobile (7,203, delta -0.4%), and the NVIDIA GeForce GTX 750 (7,222, delta -0.7%). All deltas are within one percent, meaning the GTX 560 SE is statistically indistinguishable from these peers in average benchmark score. The RTX PRO 5000’s average score of 6,407 places it near the NVIDIA GeForce GTX 460 SE (6,389, delta 0.3%), the NVIDIA GeForce GTX 580M (6,389, delta 0.3%), the AMD Radeon Vega 10 Mobile (6,476, delta -1.1%), and the NVIDIA Quadro M5000M (6,481, delta -1.1%). These are again very tight margins, all within about one percent. Notably, the RTX PRO 5000’s average benchmark score is dragged down by its low Passmark DirectX scores (78–311), despite its strong G3D and compute results, while its percentile rank of 37 is actually below the GTX 560 SE’s percentile of 39.

Architecture Differences

The two cards are separated by more than a decade of architectural evolution. The GTX 560 SE uses the GF114 chip, based on Fermi 2.0 architecture, manufactured on a 40 nm process at TSMC. It packs 1,950 million transistors into a 332 mm² die, yielding a transistor density of 5.9 million per square millimeter. The RTX PRO 5000 uses the GB202 chip, based on Blackwell 2.0 architecture, built on a 5 nm process, also at TSMC. It contains 92,200 million transistors on a 750 mm² die, giving a density of 122.9 million per square millimeter. That is a 47-fold increase in transistor count and roughly a 21-fold increase in density, reflecting the massive scaling of semiconductor fabrication.

Memory architecture is another fundamental divergence. The GTX 560 SE has 1,024 MB of GDDR5 on a 192-bit bus, delivering 91.87 GB/s of bandwidth. The RTX PRO 5000 has 72 GB of GDDR7 on a 384-bit bus, delivering 1.34 TB/s. That is a 72-fold increase in capacity and roughly a 14.6-fold increase in bandwidth. The RTX PRO 5000’s memory clock is listed at 1,750 MHz with 28 Gbps effective, while the GTX 560 SE’s memory runs at 957 MHz with 3.8 Gbps effective. The GTX 560 SE has 288 shading units, 48 texture mapping units, and 24 ROPs. The RTX PRO 5000 has 14,080 shading units, 440 TMUs, and 160 ROPs. It also adds 110 ray tracing cores and 440 tensor cores, features entirely absent from the Fermi-based GTX 560 SE.

Compute throughput scales correspondingly. The GTX 560 SE delivers 847.9 GFLOPS of FP32 performance, with a pixel rate of 8.832 GPixel/s and a texture rate of 35.33 GTexel/s. The RTX PRO 5000 delivers 66.94 TFLOPS FP32, a 380.3 GPixel/s pixel rate, and a 1,045.9 GTexel/s texture rate. The RTX PRO 5000 also offers FP16 at 66.94 TFLOPS (1:1 ratio with FP32), while the GTX 560 SE has no listed FP16 capability. The power and interface differences are equally stark: the GTX 560 SE is a 150 W dual-slot card with two 6-pin power connectors and a 450 W suggested PSU, while the RTX PRO 5000 is a 300 W dual-slot card with one 16-pin connector and a 700 W suggested PSU. The GTX 560 SE uses PCIe 2.0 x16 and outputs 2x DVI plus 1x mini-HDMI 1.3a. The RTX PRO 5000 uses PCIe 5.0 x16 and outputs 4x DisplayPort 2.1b. The GTX 560 SE supports DirectX 12 (11_0) and OpenGL 4.6, while the RTX PRO 5000 supports DirectX 12 Ultimate (12_2), OpenGL 4.6, and Vulkan 1.4.

FAQ

Q: Which card has the higher average benchmark score?

A: The GTX 560 SE has an average benchmark score of 7,171, while the RTX PRO 5000 has an average of 6,407. However, the RTX PRO 5000’s average is pulled down by its very low Passmark DirectX scores (78 for DX12, 175 for DX10, 219 for DX11), which are not representative of its G3D or compute performance.

Q: How do the two cards compare in transistor density?

A: The RTX PRO 5000 has a transistor density of 122.9M per mm², while the GTX 560 SE has 5.9M per mm². The RTX PRO 5000 also has a much larger die (750 mm² vs 332 mm²) and a much higher total transistor count (92,200 million vs 1,950 million).

Q: What is the memory bandwidth difference?

A: The RTX PRO 5000 offers 1.34 TB/s of bandwidth with 72 GB of GDDR7 on a 384-bit bus. The GTX 560 SE offers 91.87 GB/s with 1,024 MB of GDDR5 on a 192-bit bus. The RTX PRO 5000 has roughly 14.6 times the bandwidth and 72 times the capacity.

Q: Are ray tracing or tensor cores present on either card?

A: Only the RTX PRO 5000 has ray tracing cores (110) and tensor cores (440). The GTX 560 SE, based on Fermi 2.0, has neither feature listed.

Q: Which card has a higher percentile ranking among all GPUs?

A: The GTX 560 SE ranks in the 39th percentile, while the RTX PRO 5000 ranks in the 37th percentile. This means the GTX 560 SE sits slightly higher in the overall distribution despite its far older architecture and lower raw specs.

Q: What are the power and interface requirements?

A: The GTX 560 SE has a 150 W TDP with a 450 W suggested PSU and two 6-pin connectors, using PCIe 2.0 x16. The RTX PRO 5000 has a 300 W TDP with a 700 W suggested PSU and one 16-pin connector, using PCIe 5.0 x16.

The Verdict

The data paints a clear picture of two cards built for entirely different eras and workloads. The GTX 560 SE is an end-of-life Fermi part from the GeForce 500 generation, released in February 2012. It has a single OpenCL benchmark score of 7,171 and a percentile rank of 39. The RTX PRO 5000 is an active Blackwell PRO workstation card, released in October 2025. It has a Passmark G3D score of 24,310 and a GPU compute score of 15,667, but its average benchmark score of 6,407 is lower than the GTX 560 SE’s due to very low Passmark DirectX scores. The RTX PRO 5000’s percentile rank of 37 is also below the GTX 560 SE’s 39.

For raw modern compute and graphics workloads, the RTX PRO 5000 is overwhelmingly more capable by every architectural measure: it has 14,080 shading units versus 288, 66.94 TFLOPS FP32 versus 847.9 GFLOPS, 1.34 TB/s bandwidth versus 91.87 GB/s, and 72 GB memory versus 1,024 MB. It also adds ray tracing, tensor cores, and Vulkan support. The GTX 560 SE, however, appears more consistent in its benchmark results, with no sub-300 scores in its profile. The RTX PRO 5000’s Passmark DirectX 12 score of 78 and DirectX 10 score of 175 are anomalously low for a card with its specifications, suggesting either driver or benchmark-specific issues. The verdict is not about which card is "better" in absolute terms—the RTX PRO 5000 wins decisively on paper—but about which card is better suited to which tasks. For modern workstation workloads, the RTX PRO 5000 is the only rational choice. For legacy DirectX 9/11 gaming, the GTX 560 SE may actually provide a more stable experience in this database’s limited measurements.

Specification Differences

| Specification | GTX 560 SE | RTX PRO 5000 72 GB |

|---|---|---|

| Chip | GF114 | GB202 |

| Architecture | Fermi 2.0 | Blackwell 2.0 |

| Generation | GeForce 500 | Blackwell PRO W (x000) |

| Process Node | 40 nm | 5 nm |

| Transistors | 1,950 million | 92,200 million |

| Die Size | 332 mm² | 750 mm² |

| Transistor Density | 5.9M / mm² | 122.9M / mm² |

| Base Clock | — | 1740 MHz |

| Boost Clock | — | 2377 MHz |

| Memory Clock | 957 MHz / 3.8 Gbps effective | 1750 MHz / 28 Gbps effective |

| Memory Size | 1024 MB | 72 GB |

| Memory Type | GDDR5 | GDDR7 |

| Memory Bus | 192 bit | 384 bit |

| Bandwidth | 91.87 GB/s | 1.34 TB/s |

| Shading Units | 288 | 14080 |

| TMUs | 48 | 440 |

| ROPs | 24 | 160 |

| RT Cores | — | 110 |

| Tensor Cores | — | 440 |

| Pixel Rate | 8.832 GPixel/s | 380.3 GPixel/s |

| Texture Rate | 35.33 GTexel/s | 1,045.9 GTexel/s |

| FP32 | 847.9 GFLOPS | 66.94 TFLOPS |

| FP16 | — | 66.94 TFLOPS (1:1) |

| TDP | 150 W | 300 W |

| Power Connectors | 2x 6-pin | 1x 16-pin |

| Suggested PSU | 450 W | 700 W |

| Bus Interface | PCIe 2.0 x16 | PCIe 5.0 x16 |

| Display Outputs | 2x DVI, 1x mini-HDMI 1.3a | 4x DisplayPort 2.1b |

| DirectX | 12 (11_0) | 12 Ultimate (12_2) |

| Vulkan | — | 1.4 |

| Dimensions | 210 mm / 8.3 inches | 267 mm / 10.5 inches, 111 mm / 4.4 inches height, 40 mm / 1.6 inches width |

| Production Status | End-of-life | Active |

| Release Date | 2012-02-19 | 2025-10-20 |

Where Each One Wins

The GTX 560 SE wins in benchmark consistency and percentile placement. Its average score of 7,171 places it in the 39th percentile, above the RTX PRO 5000’s 37th percentile. Its nearest rivals (Iris Pro P580, GTX 970, Vega 8 Mobile, GTX 750) all fall within 0.7% of its score, showing that it performs at a very predictable level relative to its contemporaries. In the limited benchmark data available, the GTX 560 SE has no scores below its single OpenCL result, so there is no evidence of any particular weakness.

The RTX PRO 5000 wins decisively in every raw specification category that matters for modern workloads. It has 48.9 times the shading units, 9.2 times the TMUs, 6.7 times the ROPs, 78.9 times the FP32 throughput, 14.6 times the memory bandwidth, and 72 times the memory capacity. It adds 110 ray tracing cores and 440 tensor cores, enabling features the GTX 560 SE cannot support at all. Its Passmark G3D score of 24,310 and GPU compute score of 15,667 are far beyond anything the GTX 560 SE could produce, and its 3DMark Steel Nomad DX12 score of 9,579.5 reflects modern API performance. The RTX PRO 5000 also supports Vulkan 1.4 and DirectX 12 Ultimate, while the GTX 560 SE is limited to DirectX 12 (11_0) with no Vulkan support. The RTX PRO 5000 is the clear choice for any workload involving ray tracing, tensor operations, large memory footprints (e.g., 72 GB datasets), or modern APIs. The GTX 560 SE is the choice only for legacy DirectX 9/11 scenarios where its consistency and lower power draw (150 W vs 300 W) might be preferable, though its lack of modern features and end-of-life status make it a poor long-term investment.

DETAILED SPECIFICATIONS

SPECIFICATION
GTX 560 SE
RTX PRO 5000 72 GB Blackwell
Core Specs
Shading Units
288
14,080 +4788.9%
Shaders
288
14,080 +4788.9%
TMUs
48
440 +816.7%
ROPs
24
160 +566.7%
SM Count
6
110 +1733.3%
Clocks
Base Clock
—
1740 MHz
Boost Clock
—
2377 MHz
GPU Clock
736 MHz
—
Shader Clock
1472 MHz
—
Memory Clock
957 MHz 3.8 Gbps effective
1750 MHz 28 Gbps effective
Memory
Memory Size
1024 MB
72 GB
VRAM (MB)
1,024
73,728 +7100.0%
Memory Type
GDDR5
GDDR7
Memory Bus
192 bit
384 bit
Bandwidth
91.87 GB/s
1.34 TB/s
Cache
L1 Cache
64 KB (per SM)
128 KB (per SM)
L2 Cache
384 KB
96 MB
Performance
Pixel Rate
8.832 GPixel/s
380.3 GPixel/s
Texture Rate
35.33 GTexel/s
1,045.9 GTexel/s
FP32 (TFLOPS)
847.9 GFLOPS
66.94 TFLOPS
FP64 (TFLOPS)
70.66 GFLOPS (1:12)
1,045.9 GFLOPS (1:64)
FP16 (TFLOPS)
—
66.94 TFLOPS (1:1)
AI/RT
RT Cores
—
110
Tensor Cores
—
440
Power
TDP
150 W
300 W
TDP (W)
150
300 +100.0%
Suggested PSU
450 W
700 W
Power Connectors
2x 6-pin
1x 16-pin
Architecture
Architecture
Fermi 2.0
Blackwell 2.0
GPU Name
GF114
GB202
Generation
GeForce 500
Blackwell PRO W (x000)
Process Size
40 nm
5 nm
Transistors
1,950 million
92,200 million
Die Size
332 mm²
750 mm²
Foundry
TSMC
TSMC
Density
5.9M / mm²
122.9M / mm²
API Support
DirectX
12 (11_0)
12 Ultimate (12_2)
OpenGL
4.6
4.6
Vulkan
—
1.4
OpenCL
1.1
3.0
CUDA
2.1
12.0
Shader Model
5.1
6.9
Physical
Slot Width
Dual-slot
Dual-slot
Length
210 mm 8.3 inches
267 mm 10.5 inches
Height
—
111 mm 4.4 inches
Outputs
2x DVI1x mini-HDMI 1.3a
4x DisplayPort 2.1b
Bus Interface
PCIe 2.0 x16
PCIe 5.0 x16
Other
Production
End-of-life
Active
Predecessor
GeForce 400
Workstation Ada
Successor
GeForce 600
—
View GeForce GTX 560 SE Details View RTX PRO 5000 72 GB Blackwell Details