AMD Radeon R7 Graphics vs NVIDIA GeForce RTX 5060 Ti 8 GB Comparison

AMD
RADEON

AMD Radeon R7 Graphics

CORE STATE Spectre Lite
VRAM System Shared
CLOCK SPEED —
TDP 25 W
BUS WIDTH System Shared
ARCHITECTURE GCN 2.0
nm
PROCESS 28 nm
LAUNCH DATE 2014
VS
NVIDIA
GEFORCE

GeForce RTX 5060 Ti 8 GB

CORE STATE GB206
VRAM 8 GB
CLOCK SPEED 2572 MHz
TDP 180 W
BUS WIDTH 128 bit
ARCHITECTURE Blackwell 2.0
nm
PROCESS 5 nm
LAUNCH DATE 2025

PERFORMANCE BENCHMARKS

geekbench_opencl
4,015
N/A
geekbench_vulkan
5,980
N/A
3dmark_3dmark_steel_nomad_dx12
N/A
4,019
passmark_directx_10
N/A
142
passmark_directx_11
N/A
220
passmark_directx_12
N/A
82
passmark_directx_9
N/A
228
passmark_g2d
N/A
1,169
passmark_g3d
N/A
21,981
passmark_gpu_compute
N/A
11,365

Analysis: AMD Radeon R7 Graphics vs NVIDIA GeForce RTX 5060 Ti 8 GB

AMD Radeon R7 Graphics and NVIDIA GeForce RTX 5060 Ti 8 GB represent two extremes of the GPU spectrum, separated by over a decade of silicon progress and entirely different market positions. The R7 is a 2014-era integrated graphics processor embedded in a 28 nm APU, while the RTX 5060 Ti is a 2025 discrete add-in card built on TSMC's 5 nm process. Benchmark data shows the RTX 5060 Ti utterly dominates in raw compute and modern API support, but the R7 holds a curious statistical edge in average benchmark scores due to the specific tests recorded. This analysis breaks down where each part actually wins, what the numbers mean, and who should consider which.

Where Each One Wins

The RTX 5060 Ti 8 GB wins in every meaningful performance category where data exists. Its PassMark G3D score of 21,981 crushes the R7's entire benchmark portfolio, and its 23.70 TFLOPS FP32 throughput is roughly 43 times higher than the R7's 553.0 GFLOPS. In geometry processing, the RTX 5060 Ti delivers 370.4 GTexel/s texture rate versus 17.28 GTexel/s on the R7, and its pixel rate of 123.5 GPixel/s dwarfs the R7's 5.760 GPixel/s. The 5060 Ti also brings hardware ray tracing with 36 RT cores and 144 tensor cores, features entirely absent from the R7.

The AMD Radeon R7 Graphics wins in one narrow statistical category: average benchmark score. Its avgBenchmarkScore of 4998 edges out the RTX 5060 Ti's 4901, driven by the R7's Geekbench Vulkan score of 5980 and OpenCL score of 4015. The RTX 5060 Ti's own benchmark results are mixed, with a strong 3DMark Steel Nomad DX12 score of 4019 but surprisingly low PassMark DirectX 10, 11, and 12 scores of 142, 220, and 82 respectively. These PassMark numbers appear anomalous for a modern GPU, yet they drag down the 5060 Ti's average. In practical terms, the R7's "win" is a statistical artifact of limited test data, not a real performance advantage.

FAQ

Q: Which GPU has the higher average benchmark score?

A: The AMD Radeon R7 Graphics records an average benchmark score of 4998, while the NVIDIA GeForce RTX 5060 Ti 8 GB averages 4901. The R7 leads by roughly 2%, but this reflects the specific tests available, not overall capability.

Q: What is the single biggest performance gap between the two?

A: In FP32 compute, the RTX 5060 Ti delivers 23.70 TFLOPS versus the R7's 553.0 GFLOPS. That is a 42.9x difference, making it the largest numerical gap in any comparable specification.

Q: Does the Radeon R7 Graphics support ray tracing?

A: No. The R7 has no RT cores or tensor cores listed. The RTX 5060 Ti includes 36 RT cores and 144 tensor cores, enabling hardware-accelerated ray tracing and DLSS-style features that the R7 cannot perform.

Q: How do the two compare in memory bandwidth?

A: The RTX 5060 Ti uses 8 GB of GDDR7 on a 128-bit bus with 448.0 GB/s bandwidth. The R7 uses system-shared memory with bandwidth listed as "System Dependent," meaning it relies on the host system's RAM speed and has no dedicated VRAM.

Q: Which card is currently in production?

A: The RTX 5060 Ti 8 GB is listed as "Active" production status. The Radeon R7 Graphics is "End-of-life," having been released in February 2014 and succeeded by GCN 3.0 IGP.

Q: What API level does each GPU support?

A: The RTX 5060 Ti supports DirectX 12 Ultimate (12_2), OpenGL 4.6, and Vulkan 1.4. The R7 supports DirectX 12 (12_0), OpenGL 4.6, and Vulkan 1.2.170, making it a full DirectX 12 generation behind.

Head-to-Head Benchmarks

Direct benchmark comparisons between these two GPUs are sparse, as the headToHeadBenchmarks array is empty. However, the available individual scores paint a clear picture. The RTX 5060 Ti's PassMark G3D score of 21,981 is its standout result, representing a full 3D rendering workload. The R7's best score is its Geekbench Vulkan result of 5980, which is respectable for an integrated GPU but still only about 27% of the 5060 Ti's PassMark G3D figure.

In compute workloads, the RTX 5060 Ti's PassMark GPU Compute score of 11,365 demonstrates strong parallel processing capability. The R7's Geekbench OpenCL score of 4015 is its only compute-oriented result, and it trails the 5060 Ti's compute score by roughly 2.8x. The 5060 Ti also shows a 3DMark Steel Nomad DX12 score of 4019, specifically testing modern DirectX 12 rendering techniques that the R7's older GCN 2.0 architecture cannot efficiently execute despite its nominal DirectX 12 (12_0) support.

The RTX 5060 Ti's PassMark DirectX 9 and 11 scores of 228 and 220 are unexpectedly low, likely reflecting driver or workload differences rather than hardware limitations. The R7 has no comparable PassMark scores, so these specific results cannot be directly compared. The 5060 Ti's PassMark G2D score of 1169 indicates strong 2D performance, but the R7 lacks a similar metric. Overall, the data shows a massive performance gulf in favor of the RTX 5060 Ti, with the R7's only statistical advantage being its higher Geekbench Vulkan score relative to the 5060 Ti's average.

Specification Differences

The two GPUs differ in nearly every measurable specification. The R7 uses 384 shading units, 24 texture mapping units, and 8 ROPs, while the RTX 5060 Ti employs 4608 shading units, 144 TMUs, and 48 ROPs — a 12x, 6x, and 6x increase respectively. Clock speeds tell a similar story: the RTX 5060 Ti has a base clock of 2407 MHz and boost of 2572 MHz, while the R7 lists no base or boost clocks, only "System Shared" memory clock. Memory configurations are completely different: the R7 uses system-shared memory with no dedicated VRAM, while the 5060 Ti has 8 GB of GDDR7 on a 128-bit bus with 448.0 GB/s bandwidth.

Power and physical specifications diverge sharply. The R7 is an IGP (integrated graphics processor) with a 25 W TDP and no power connectors, designed to be embedded in a motherboard. The RTX 5060 Ti is a dual-slot card measuring 241 mm long, 111 mm tall, and 40 mm wide, with a 180 W TDP, a single 8-pin power connector, and a suggested 450 W PSU. The bus interface differs as well: the R7 uses IGP (integrated), while the 5060 Ti uses PCIe 5.0 x8. Display outputs are "Motherboard Dependent" on the R7 versus 1x HDMI 2.1b and 3x DisplayPort 2.1b on the 5060 Ti. The 5060 Ti has a launch MSRP of 379 USD.

Architecture Differences

The architectural gap between these two GPUs spans over a decade of development. The R7 is built on AMD's GCN 2.0 architecture, specifically the Spectre Lite chip, fabricated on GlobalFoundries' 28 nm process with 2,410 million transistors on a 245 mm² die. This yields a transistor density of 9.8M per mm². The RTX 5060 Ti uses NVIDIA's Blackwell 2.0 architecture with the GB206 chip, manufactured by TSMC on a 5 nm process, packing 21,900 million transistors into a much smaller 181 mm² die for a density of 121.0M per mm² — over 12 times denser.

The R7's GCN 2.0 design, released in 2014 as part of the Kaveri APU generation, lacks dedicated ray tracing and tensor cores entirely. It relies on 384 shading units for all compute work, with a peak FP32 throughput of 553.0 GFLOPS. The RTX 5060 Ti's Blackwell 2.0 architecture introduces 36 RT cores for hardware ray tracing and 144 tensor cores for AI acceleration, alongside 4608 shading units. Its FP32 performance reaches 23.70 TFLOPS, and it supports FP16 at the same 23.70 TFLOPS rate (1:1). The API support reflects this architectural evolution: the 5060 Ti supports DirectX 12 Ultimate (12_2) and Vulkan 1.4, while the R7 is limited to DirectX 12 (12_0) and Vulkan 1.2.170. Both support OpenGL 4.6, but the feature sets enabled by those APIs are vastly different, with the 5060 Ti capable of mesh shaders, variable rate shading, and other modern rendering techniques that the R7 cannot execute.

The Verdict

The data leaves no room for ambiguity in most use cases. The RTX 5060 Ti 8 GB is the only choice for anyone running modern 3D games, GPU-accelerated compute, or ray-traced workloads. Its 23.70 TFLOPS FP32 performance, 448.0 GB/s memory bandwidth, and 8 GB of dedicated GDDR7 VRAM are absolute requirements for contemporary titles and professional applications. The 36 RT cores and 144 tensor cores enable features the R7 physically cannot implement. The 5060 Ti's PassMark G3D score of 21,981 versus the R7's best score of 5,980 (Geekbench Vulkan) quantifies a roughly 3.7x gap in raw 3D performance, and real-world differences in modern APIs would be even larger.

The AMD Radeon R7 Graphics should only be considered for legacy systems or low-power embedded applications where its 25 W TDP and IGP form factor are advantages. Its higher average benchmark score of 4998 versus 4901 is misleading, driven by the 5060 Ti's anomalously low PassMark DirectX scores. The R7's Geekbench Vulkan score of 5980 shows it can handle basic 2D and light 3D workloads, but its system-shared memory, lack of dedicated VRAM, and 2014-era GCN 2.0 architecture make it unsuitable for anything beyond casual or legacy use. The RTX 5060 Ti, despite its lower average score, is categorically superior in every meaningful performance metric, and its active production status ensures ongoing driver and software support. Choose the 5060 Ti for any new build or upgrade; choose the R7 only if you are constrained to an older platform with no discrete GPU option.

DETAILED SPECIFICATIONS

SPECIFICATION
R7 Graphics
RTX 5060 Ti 8 GB
Core Specs
Shading Units
384
4,608 +1100.0%
Shaders
384
4,608 +1100.0%
TMUs
24
144 +500.0%
ROPs
8
48 +500.0%
Compute Units
6
—
SM Count
—
36
Clocks
Base Clock
—
2407 MHz
Boost Clock
—
2572 MHz
GPU Clock
720 MHz
—
Memory Clock
System Shared
1750 MHz 28 Gbps effective
Memory
Memory Size
System Shared
8 GB
VRAM (MB)
—
8,192
Memory Type
System Shared
GDDR7
Memory Bus
System Shared
128 bit
Bandwidth
System Dependent
448.0 GB/s
Cache
L1 Cache
—
128 KB (per SM)
L2 Cache
—
32 MB
Performance
Pixel Rate
5.760 GPixel/s
123.5 GPixel/s
Texture Rate
17.28 GTexel/s
370.4 GTexel/s
FP32 (TFLOPS)
553.0 GFLOPS
23.70 TFLOPS
FP64 (TFLOPS)
34.56 GFLOPS (1:16)
370.4 GFLOPS (1:64)
FP16 (TFLOPS)
—
23.70 TFLOPS (1:1)
AI/RT
RT Cores
—
36
Tensor Cores
—
144
Power
TDP
25 W
180 W
TDP (W)
25
180 +620.0%
Suggested PSU
—
450 W
Power Connectors
—
1x 8-pin
Architecture
Architecture
GCN 2.0
Blackwell 2.0
GPU Name
Spectre Lite
GB206
Generation
GCN 2.0 IGP (Kaveri)
GeForce 50
Process Size
28 nm
5 nm
Transistors
2,410 million
21,900 million
Die Size
245 mm²
181 mm²
Foundry
GlobalFoundries
TSMC
Density
9.8M / mm²
121.0M / mm²
API Support
DirectX
12 (12_0)
12 Ultimate (12_2)
OpenGL
4.6
4.6
Vulkan
1.2.170
1.4
OpenCL
2.1
3.0
CUDA
—
12.0
Shader Model
6.5
6.9
Physical
Slot Width
IGP
Dual-slot
Length
—
241 mm 9.5 inches
Height
—
111 mm 4.4 inches
Outputs
Motherboard Dependent
1x HDMI 2.1b3x DisplayPort 2.1b
Bus Interface
IGP
PCIe 5.0 x8
Other
Launch Price
—
379 USD
Production
End-of-life
Active
Predecessor
TeraScale 3 IGP
GeForce 40
Successor
GCN 3.0 IGP
GeForce 60
View Radeon R7 Graphics Details View GeForce RTX 5060 Ti 8 GB Details