AMD FirePro W4190M vs AMD Radeon RX 9060 XT 8 GB Comparison

AMD
RADEON

AMD FirePro W4190M

CORE STATE Opal
VRAM 2 GB
CLOCK SPEED 900 MHz
TDP —
BUS WIDTH 128 bit
ARCHITECTURE GCN 1.0
nm
PROCESS 28 nm
LAUNCH DATE 2015
VS
AMD
RADEON

Radeon RX 9060 XT 8 GB

CORE STATE Navi 44
VRAM 8 GB
CLOCK SPEED 3130 MHz
TDP 150 W
BUS WIDTH 128 bit
ARCHITECTURE RDNA 4.0
nm
PROCESS 4 nm
LAUNCH DATE 2025

PERFORMANCE BENCHMARKS

geekbench_opencl
4,505
N/A
3dmark_3dmark_steel_nomad_dx12
N/A
4,093

Analysis: AMD FirePro W4190M vs AMD Radeon RX 9060 XT 8 GB

The Verdict

The data presents a stark generational contrast. The AMD FirePro W4190M is an end-of-life mobile workstation chip from 2015, built on the aging GCN 1.0 architecture. The AMD Radeon RX 9060 XT 8 GB is an active, desktop-class part from 2025, built on the modern RDNA 4.0 architecture. Benchmark results place them in surprisingly similar overall percentiles — the FirePro sits at the 26th percentile of all GPUs, while the RX 9060 XT sits at the 24th percentile — but this is a statistical artifact of the unrelated benchmark suites used. The FirePro’s only recorded score is 4505 in Geekbench OpenCL, while the RX 9060 XT’s only recorded score is 4093 in 3DMark Steel Nomad DX12. These tests measure different workloads, so direct cross-comparison is impossible.

From the data alone, the RX 9060 XT is the only sensible choice for any current workload. It offers 8 GB of GDDR6 memory versus 2 GB of GDDR5, a 150 W TDP with a dedicated power connector, and support for DirectX 12 Ultimate. The FirePro W4190M is a 28 nm part with a 950 million transistor count, a 77 mm² die, and a 64.00 GB/s memory bandwidth. Its production status is end-of-life. The RX 9060 XT is active, with a launch MSRP of 299 USD. For any new purchase or upgrade, the RX 9060 XT is the data-backed choice. The FirePro W4190M should only be considered by someone maintaining legacy mobile workstation hardware, and even then, only if the specific software requires that exact GCN 1.0 feature set.

Architecture Differences

The architectural gap between these two GPUs is immense. The FirePro W4190M uses the Opal chip, based on GCN 1.0, manufactured on a 28 nm process at TSMC. It packs 950 million transistors onto a 77 mm² die, resulting in a transistor density of 12.3M / mm². The Radeon RX 9060 XT uses the Navi 44 chip, based on RDNA 4.0, manufactured on a 4 nm process, also at TSMC. It contains 29,700 million transistors on a 199 mm² die, for a transistor density of 149.2M / mm². The RX 9060 XT is over 30 times denser in terms of transistor count per square millimeter.

The RX 9060 XT features 2048 shading units, 128 texture mapping units, and 64 render output units. It also includes 32 dedicated ray tracing cores. The FirePro W4190M has 384 shading units, 24 TMUs, and 8 ROPs, with no ray tracing cores. The RX 9060 XT supports DirectX 12 Ultimate (12_2) and Vulkan 1.4, while the FirePro supports DirectX 12 (11_1) and Vulkan 1.2.170. Both support OpenGL 4.6. The RX 9060 XT offers a 1:1 FP16 to FP32 ratio, with both at 25.64 TFLOPS, whereas the FirePro has no listed FP16 capability.

The memory subsystems are also fundamentally different. The FirePro uses 2 GB of GDDR5 on a 128-bit bus, yielding 64.00 GB/s of bandwidth. The RX 9060 XT uses 8 GB of GDDR6 on the same 128-bit bus width, but achieves 322.3 GB/s of bandwidth — a fivefold increase. The RX 9060 XT also has a much higher boost clock at 3130 MHz, compared to the FirePro’s 900 MHz. The bus interface differs as well: the FirePro uses PCIe 3.0 x8, while the RX 9060 XT uses PCIe 5.0 x16.

Head-to-Head Benchmarks

There are no direct head-to-head benchmark results recorded between these two specific GPUs. The FirePro W4190M has a single Geekbench OpenCL score of 4505, while the RX 9060 XT has a single 3DMark Steel Nomad DX12 score of 4093. Because these are different tests from different suites, the numbers cannot be compared as a measure of relative performance.

Looking at each card’s nearest rivals provides context within its own benchmark. The FirePro W4190M scores 0.1% higher than the AMD Radeon R7 M260 (4499), 1.2% lower than the Intel HD Graphics P530 (4560), 1.4% lower than the AMD Radeon RX 560 (4569), and 1.6% lower than the AMD Radeon R5 M230 (4577). This places the FirePro in a narrow performance band around 4500 in OpenCL compute tasks.

The RX 9060 XT, in its 3DMark Steel Nomad test, scores 0.4% higher than the Intel HD Graphics 630 (4075), 1.4% lower than the NVIDIA Quadro K2100M (4151), 1.5% higher than the NVIDIA GeForce GT 755M (4033), and 1.8% lower than the AMD Radeon R5 M330 (4170). This indicates that, in this specific DX12 test, the RX 9060 XT performs at a level comparable to older mobile and integrated graphics solutions. This is a notable result, suggesting that the RX 9060 XT’s raw compute power may not translate to an equally dominant showing in all synthetic benchmarks, or that the Steel Nomad test is particularly demanding on this architecture.

Specification Differences

The following fields differ between the two parts, based solely on the FACT PACK:

  • Process Node: FirePro W4190M is 28 nm; RX 9060 XT is 4 nm.
  • Transistors: FirePro has 950 million; RX 9060 XT has 29,700 million.
  • Die Size: FirePro is 77 mm²; RX 9060 XT is 199 mm².
  • Transistor Density: FirePro is 12.3M / mm²; RX 9060 XT is 149.2M / mm².
  • Base Clock: FirePro is 825 MHz; RX 9060 XT is 1700 MHz.
  • Boost Clock: FirePro is 900 MHz; RX 9060 XT is 3130 MHz.
  • Game Clock: FirePro has none listed; RX 9060 XT is 2530 MHz.
  • Memory Clock: FirePro is 1000 MHz (4 Gbps effective); RX 9060 XT is 2518 MHz (20.1 Gbps effective).
  • Memory Size: FirePro is 2 GB; RX 9060 XT is 8 GB.
  • Memory Type: FirePro is GDDR5; RX 9060 XT is GDDR6.
  • Memory Bandwidth: FirePro is 64.00 GB/s; RX 9060 XT is 322.3 GB/s.
  • Shading Units: FirePro has 384; RX 9060 XT has 2048.
  • TMUs: FirePro has 24; RX 9060 XT has 128.
  • ROPs: FirePro has 8; RX 9060 XT has 64.
  • Ray Tracing Cores: FirePro has none; RX 9060 XT has 32.
  • Pixel Rate: FirePro is 7.200 GPixel/s; RX 9060 XT is 200.3 GPixel/s.
  • Texture Rate: FirePro is 21.60 GTexel/s; RX 9060 XT is 400.6 GTexel/s.
  • FP32: FirePro is 691.2 GFLOPS; RX 9060 XT is 25.64 TFLOPS.
  • FP16: FirePro has none listed; RX 9060 XT is 25.64 TFLOPS (1:1).
  • TDP: FirePro has none listed; RX 9060 XT is 150 W.
  • Slot Width: FirePro is MXM Module; RX 9060 XT is Dual-slot.
  • Power Connectors: FirePro is None; RX 9060 XT is 1x 8-pin.
  • Suggested PSU: FirePro has none listed; RX 9060 XT is 450 W.
  • Bus Interface: FirePro is PCIe 3.0 x8; RX 9060 XT is PCIe 5.0 x16.
  • Display Outputs: FirePro is Portable Device Dependent; RX 9060 XT is 1x HDMI 2.1b, 2x DisplayPort 2.1a.
  • DirectX Support: FirePro is 12 (11_1); RX 9060 XT is 12 Ultimate (12_2).
  • Vulkan Support: FirePro is 1.2.170; RX 9060 XT is 1.4.
  • Production Status: FirePro is End-of-life; RX 9060 XT is Active.
  • Release Date: FirePro is 2015-11-11; RX 9060 XT is 2025-06-03.
  • Predecessor: FirePro is FirePro Mobility; RX 9060 XT is Navi III.
  • Successor: FirePro is Radeon Pro Mobile; RX 9060 XT has none listed.
  • Launch MSRP: FirePro has none listed; RX 9060 XT is 299 USD.
  • Benchmark Test: FirePro uses Geekbench OpenCL (4505); RX 9060 XT uses 3DMark Steel Nomad DX12 (4093).
  • Percentile: FirePro is 26th; RX 9060 XT is 24th.

FAQ

Q: Which GPU has more memory bandwidth?

A: The AMD Radeon RX 9060 XT 8 GB has a memory bandwidth of 322.3 GB/s, compared to the AMD FirePro W4190M’s 64.00 GB/s.

Q: Does the FirePro W4190M support ray tracing?

A: No. The FirePro W4190M has no ray tracing cores listed, while the Radeon RX 9060 XT has 32 ray tracing cores.

Q: What is the transistor density difference?

A: The RX 9060 XT has a transistor density of 149.2M / mm², which is over twelve times the 12.3M / mm² of the FirePro W4190M.

Q: Which GPU is currently in production?

A: The Radeon RX 9060 XT is marked as Active, while the FirePro W4190M is marked as End-of-life.

Q: What is the launch MSRP of the RX 9060 XT?

A: The launch MSRP of the Radeon RX 9060 XT 8 GB is 299 USD. The FirePro W4190M has no launch MSRP listed.

Q: Are their benchmark percentiles similar?

A: Yes, the FirePro W4190M sits at the 26th percentile of all GPUs, and the RX 9060 XT sits at the 24th percentile. However, they were tested with different benchmarks, so this is not a direct performance comparison.

Where Each One Wins

The Radeon RX 9060 XT wins decisively in nearly every measurable specification. It has a significantly higher pixel rate (200.3 GPixel/s vs 7.200 GPixel/s) and texture rate (400.6 GTexel/s vs 21.60 GTexel/s). Its FP32 compute is 25.64 TFLOPS versus 691.2 GFLOPS. It has 8 GB of memory versus 2 GB, and its memory bandwidth is over five times higher. It supports modern APIs including DirectX 12 Ultimate and Vulkan 1.4. It has ray tracing cores. It is an active product with a 2025 release date.

The FirePro W4190M wins only in specific legacy contexts. It is an MXM module, which means it is designed for mobile workstations that accept that form factor, whereas the RX 9060 XT is a dual-slot desktop card. The FirePro has no external power connector requirement and no listed TDP, suggesting it is a low-power mobile part. The RX 9060 XT requires a 150 W TDP, a 1x 8-pin power connector, and a 450 W suggested PSU. Therefore, the FirePro is the only one of the two that could be installed in a compatible MXM mobile chassis without power supply changes.

In terms of benchmark wins, the data shows each card has one recorded score in different tests. Neither can be said to win a head-to-head contest because no such benchmark exists. The RX 9060 XT is the clear winner for any modern desktop use case, including gaming, content creation, or compute workloads that benefit from FP16 and ray tracing. The FirePro W4190M is the appropriate choice only for legacy mobile workstation replacements where the MXM slot and GCN 1.0 feature set are required.

DETAILED SPECIFICATIONS

SPECIFICATION
FirePro W4190M
RX 9060 XT 8 GB
Core Specs
Shading Units
384
2,048 +433.3%
Shaders
384
2,048 +433.3%
TMUs
24
128 +433.3%
ROPs
8
64 +700.0%
Compute Units
6
32 +433.3%
Clocks
Base Clock
825 MHz
1700 MHz
Boost Clock
900 MHz
3130 MHz
Game Clock
—
2530 MHz
Memory Clock
1000 MHz 4 Gbps effective
2518 MHz 20.1 Gbps effective
Memory
Memory Size
2 GB
8 GB
VRAM (MB)
2,048
8,192 +300.0%
Memory Type
GDDR5
GDDR6
Memory Bus
128 bit
128 bit
Bandwidth
64.00 GB/s
322.3 GB/s
Cache
L1 Cache
16 KB (per CU)
—
L2 Cache
256 KB
4 MB
L3 Cache
—
32 MB
L0 Cache
—
32 KB per WGP
Performance
Pixel Rate
7.200 GPixel/s
200.3 GPixel/s
Texture Rate
21.60 GTexel/s
400.6 GTexel/s
FP32 (TFLOPS)
691.2 GFLOPS
25.64 TFLOPS
FP64 (TFLOPS)
43.20 GFLOPS (1:16)
801.3 GFLOPS (1:32)
FP16 (TFLOPS)
—
25.64 TFLOPS (1:1)
AI/RT
RT Cores
—
32
Matrix Cores
—
64
Power
TDP
—
150 W
TDP (W)
—
150
Suggested PSU
—
450 W
Power Connectors
None
1x 8-pin
Architecture
Architecture
GCN 1.0
RDNA 4.0
GPU Name
Opal
Navi 44
Codename
—
Strix Point
Generation
FirePro Mobile (Wx100M)
Navi IV (RX 9000)
Process Size
28 nm
4 nm
Transistors
950 million
29,700 million
Die Size
77 mm²
199 mm²
Foundry
TSMC
TSMC
Density
12.3M / mm²
149.2M / mm²
API Support
DirectX
12 (11_1)
12 Ultimate (12_2)
OpenGL
4.6
4.6
Vulkan
1.2.170
1.4
OpenCL
2.1 (1.2)
2.2
Shader Model
6.5 (5.1)
6.9
Physical
Slot Width
MXM Module
Dual-slot
Outputs
Portable Device Dependent
1x HDMI 2.1b2x DisplayPort 2.1a
Bus Interface
PCIe 3.0 x8
PCIe 5.0 x16
Other
Launch Price
—
299 USD
Production
End-of-life
Active
Predecessor
FirePro Mobility
Navi III
Successor
Radeon Pro Mobile
—
View FirePro W4190M Details View Radeon RX 9060 XT 8 GB Details