Archeage
This combination provides smooth gameplay with an average of 64 FPS, suitable for most gaming scenarios.
Average FPS: resolution vs quality settings
| Ultra | High | Medium | Low | |
|---|---|---|---|---|
| 4K Ultra HD | 20 | 30 | 44 | 50 |
| 1440p QHD | 36 | 52 | 77 | 87 |
| 1080p Full HD | 53 | 78 | 114 | 129 |
Cell color: green is 120+ FPS, teal is 60+, amber is 30+, red is below 30.
Archeage with Intel Core Ultra 7 265 + AMD Radeon RX 6600 XT, In-Depth Analysis
The Intel Core Ultra 7 265 paired with the AMD Radeon RX 6600 XT delivers a playable but decidedly mid-range experience in Archeage, with the data showing that this combination ranks in the 28th percentile of tested combos and is consistently constrained by the GPU at higher resolutions. The measured frame rates reveal a system that can handle 1080p gaming with high settings comfortably, but which struggles to maintain fluid motion at 4K, particularly when the preset is raised beyond Medium.
Resolution Scaling
The frame rate drop from 1080p to 4K is steep and tells a clear story about which component is the bottleneck in this pairing. At Low settings, the average FPS falls from 129 at 1920x1080 to 87 at 2560x1440, a reduction of roughly one-third, and then further to 50 at 3840x2160. That represents a 61% loss from 1080p to 4K at the lowest preset, a scaling pattern that points directly at the GPU as the limiting factor, since the CPU’s workload does not scale nearly as dramatically with resolution.
Looking at Medium settings, the pattern is similar. The average of 114 FPS at 1080p drops to 77 at 1440p, a 32% decline, and then to 44 at 4K, a 61% drop from the 1080p figure. The minimum frame rate at 1440p Medium is 66 FPS, while at 4K Medium it is 38 FPS, showing that not only the average but also the worst-case performance degrades substantially as pixel count increases. The gap between 1440p and 4K is consistently larger than the gap between 1080p and 1440p, which is typical of a GPU that runs out of raw throughput and memory bandwidth at higher resolutions.
At High settings, the trend continues: 78 FPS at 1080p, 52 at 1440p, and 30 at 4K. The percentage drop from 1080p to 1440p is 33%, while from 1440p to 4K it is 42%, indicating that the scaling becomes slightly steeper as the resolution approaches the GPU’s practical ceiling. The Ultra preset shows the most dramatic degradation: 53 FPS at 1080p, 36 at 1440p, and just 20 at 4K. The 4K Ultra figure is only 38% of the 1080p Ultra number, and at 20 FPS average, it is below the threshold of smooth interactivity for an MMORPG where quick camera movements and ability rotations matter.
The data indicates that resolution scaling in Archeage with this combo is governed almost entirely by the Radeon RX 6600 XT’s capabilities. The Core Ultra 7 265, with its 20 cores and 20 threads, is not the constraining factor at any resolution in these tests; the evidence is that frame rates fall in near-linear fashion with the pixel count increase, which is the signature of a GPU-bound scenario. Even at 1080p Low, where the CPU would have the most room to become a bottleneck, the 129 FPS average suggests the processor is feeding frames adequately without limiting the GPU. The takeaway is that users targeting 1440p or above will need to lower settings aggressively, while 1080p offers enough headroom to use medium or high presets.
GPU Role
The AMD Radeon RX 6600 XT is built on the RDNA 2.0 architecture with a Navi 23 chip, featuring 2048 shading units, 128 texture mapping units, and 64 raster output units. Its clock speeds are listed with a base of 1968 MHz, a game clock of 2359 MHz, and a boost clock of 2589 MHz. The 8 GB of GDDR6 memory on a 128-bit bus delivers 256.0 GB/s of bandwidth, which is a modest figure by modern standards but sufficient for a game like Archeage that is not particularly memory-hungry at 1080p.
The GPU’s benchmark profile shows a Passmark G3D score of 16461, placing it in the 70th percentile of all GPUs in the database. Its nearest rivals in aggregate performance are the NVIDIA GeForce GTX 1630 with an average score of 24277 (0.7% higher), the Intel Arc A350M at 24647 (0.8% lower), the NVIDIA GeForce GTX 780 Ti at 24236 (0.8% higher), and the NVIDIA GeForce RTX 2080 SUPER at 24170 (1.1% higher). These deltas are all within 1.1%, meaning that in synthetic benchmarks, this GPU is effectively tied with a group of cards spanning several generations and tiers. That context matters for Archeage: the game’s engine is from 2014, and its rendering demands are not aligned with the latest DirectX 12 Ultimate features, so the RX 6600 XT’s raw rasterization throughput is what carries the results.
In Archeage specifically, the GPU’s role becomes apparent when comparing the Low and Ultra presets at the same resolution. At 1080p, Low yields 129 FPS while Ultra yields 53 FPS, a 59% reduction. The gap narrows at 1440p (87 vs 36, a 59% reduction as well) and at 4K (50 vs 20, a 60% reduction). This consistent ~60% penalty from Low to Ultra across all resolutions confirms that the GPU is the primary driver of performance differences between settings, as the CPU’s load does not change enough with graphical presets to alter the outcome. The 8 GB VRAM capacity is likely sufficient for Archeage even at 4K Ultra, since the frame rate collapse to 20 FPS is more plausibly caused by the GPU’s compute and fillrate limits than by memory capacity exhaustion, though the data does not directly measure VRAM usage.
The RX 6600 XT’s 10.60 TFLOPS of FP32 performance and 165.7 GPixel/s pixel rate are the specifications that most directly correlate with the measured results. The 4K Medium average of 44 FPS and 4K High average of 30 FPS indicate that the GPU is operating near its limits at that resolution, while the 1080p Medium minimum of 97 FPS shows it has ample headroom at lower pixel counts. The GPU’s end-of-life production status and its 160 W TDP, with a suggested PSU of 450 W, also frame it as a mainstream part that was never intended for high-refresh 4K gaming, which is consistent with the data.
How This Combo Ranks
In the database of tested CPU and GPU combinations for Archeage, this pairing of the Intel Core Ultra 7 265 and the AMD Radeon RX 6600 XT holds a rank of 2659 out of 3708 total combos. That places it in the 28th percentile of all tested combinations, meaning that roughly 72% of other pairings deliver higher average frame rates in this game. This is a below-average result for the database, which is notable because the individual components are not low-end in absolute terms.
The CPU alone sits in the 93rd percentile of all processors, with an average benchmark score of 64640. Its nearest rivals are the AMD EPYC 4464P at 64823 (-0.3% delta), the Intel Core Ultra 7 265F at 64438 (0.3% delta), the AMD EPYC 7343 at 64202 (0.7% delta), and the AMD EPYC 9124 at 65104 (-0.7% delta). These are all server-class or near-server chips with similar multi-threaded performance, indicating that the Core Ultra 7 265 is a top-tier desktop processor in raw compute. The GPU, meanwhile, is in the 70th percentile with an average score of 24442, which is a solid mid-range result. The discrepancy between the CPU’s high percentile and the combo’s low rank in Archeage demonstrates that the game is not CPU-bound in this configuration; the limiting factor is the GPU, which drags the overall ranking down.
Comparing to other combos in the database, the 28th percentile rank suggests that many systems with weaker CPUs but stronger GPUs outperform this pairing in Archeage. The game’s release date of 2014-01-14 means its engine is old and likely more dependent on single-thread CPU performance and GPU rasterization than on multi-core scaling or modern API features. The Core Ultra 7 265’s single-core score in Cinebench R23 is 5960, which is strong, but that advantage is wasted if the GPU cannot keep up at higher resolutions. The data indicates that this combo is best suited for 1080p gaming, where the GPU can fully express itself, and that users who prioritize higher resolutions would be better served by a different GPU selection, even if it meant pairing it with a less powerful CPU.
Measured FPS Breakdown
At 1920x1080, the measured results show a clear hierarchy across presets. Low settings produce an average of 129 FPS, which is the highest figure recorded for this combo in any configuration. Medium settings yield 114 FPS average, with a minimum of 97 and a maximum of 132, indicating that even the worst-case frames stay above the 60 FPS threshold. High settings drop to 78 FPS average, while Ultra falls to 53 FPS. The step from Medium to High is a 32% reduction, and from High to Ultra is a 32% reduction as well, showing that each preset level imposes a similar performance cost at 1080p.
At 2560x1440, the averages are 87 FPS for Low, 77 FPS for Medium, 52 FPS for High, and 36 FPS for Ultra. The Medium preset’s minimum of 66 FPS and maximum of 89 FPS show that 1440p Medium is still a viable option for smooth gameplay, as the minimum stays above 60. High settings at 1440p, however, average 52 FPS, which is below the 60 FPS target for many players, and Ultra at 36 FPS is borderline for an MMORPG where frame pacing matters during large-scale battles. The drop from Medium to High at 1440p is 32%, while High to Ultra is 31%, a consistent pattern that mirrors the 1080p results.
At 3840x2160, the data becomes less encouraging. Low settings average 50 FPS, Medium averages 44 FPS with a minimum of 38 and maximum of 51, High averages 30 FPS, and Ultra averages 20 FPS. The 4K Medium minimum of 38 FPS is below the 60 FPS threshold and even dips close to the 30 FPS playability floor. High and Ultra at 4K are essentially unplayable for a game requiring responsive input, with averages of 30 and 20 respectively. The scaling from 1080p to 4K at each preset is as follows: Low falls from 129 to 50 (61% reduction), Medium from 114 to 44 (61% reduction), High from 78 to 30 (62% reduction), and Ultra from 53 to 20 (62% reduction). This uniformity across presets reinforces that resolution, not settings, is the dominant factor in performance degradation.
The minimum frame rates, where available, provide additional insight. At 1080p Medium, the minimum is 97 FPS, which is only 15% below the average of 114, suggesting good frame pacing. At 1440p Medium, the minimum of 66 is 14% below the average of 77, again a tight distribution. At 4K Medium, however, the minimum of 38 is 14% below the average of 44, but the absolute value is low enough to cause perceptible stutter in crowded scenes. This data suggests that the GPU’s frame delivery becomes less consistent as resolution increases, which is typical of a card nearing its memory bandwidth limit.
Settings Recommendations
Based on the measured frame rates, the optimal preset for this combo depends heavily on the target resolution. At 1920x1080, Medium settings offer the best balance, with an average of 114 FPS and a minimum of 97 FPS. This provides a 90 FPS cushion above the 60 FPS threshold, ensuring smooth performance even in demanding MMO scenarios with many players and effects. High settings at 1080p, at 78 FPS average, are also acceptable and provide better visual fidelity, but the 32% performance penalty over Medium may not be worth it if the user prioritizes frame rate stability. Ultra at 1080p, at 53 FPS, falls below 60 FPS and is not recommended for competitive or fast-paced gameplay.
At 2560x1440, Medium is the clear choice, with an average of 77 FPS and a minimum of 66 FPS. This is the only preset at 1440p that maintains an average above 60 FPS, and the minimum of 66 also stays above that threshold. High at 1440p averages 52 FPS, which is playable but not ideal for an MMORPG where reaction time matters, and Ultra at 36 FPS is below the playable threshold. Low at 1440p averages 87 FPS, which is higher than Medium but requires sacrificing visual quality; given that Medium already provides a comfortable margin, Low is unnecessary unless the user is particularly sensitive to frame drops.
At 3840x2160, no preset achieves a fully smooth experience. Low averages 50 FPS, which is below 60 but may be tolerable for casual play, while Medium averages 44 FPS with a minimum of 38, and High and Ultra are effectively unplayable at 30 and 20 FPS respectively. For 4K users, the recommendation is to either drop to a lower resolution or accept sub-60 FPS gameplay with Low settings. The data does not support a recommendation for 4K gaming with this combo, as even the lowest preset fails to reach the 60 FPS target.
Overall, the best experience per the measured rows is 1080p Medium, which delivers high frame rates with a minimum above 90 FPS, or 1440p Medium for users who prefer a higher resolution at the cost of some frame rate headroom. The 1080p High preset is a viable alternative for those who value visual quality over maximum FPS, as its 78 FPS average is still well within a smooth range. The Ultra preset should be avoided at all resolutions with this GPU, as it consistently reduces performance by roughly 30-40% compared to High without a correspondingly large visual benefit in a 2014-era game.
CPU Role
The Intel Core Ultra 7 265 is a 20-core, 20-thread processor based on the Arrow Lake-S architecture, built on a 3 nm process at TSMC. It has a base clock of 2.40 GHz and a boost clock of 5.30 GHz, with a 30 MB shared L3 cache and 3 MB of L2 per core. Its 65 W TDP and socket 1851 compatibility position it as a mainstream desktop part, but its benchmark scores are anything but mainstream. In Cinebench R23, it scores 42216 in multi-core and 5960 in single-core, while in Passmark it achieves 49682 in multithread and 4689 in single-thread. These figures place it in the 93rd percentile of all CPUs, with an average benchmark score of 64640.
In Archeage, however, the CPU’s role is secondary to the GPU, as evidenced by the resolution scaling data. The game, released in 2014, is an MMORPG that was designed for the hardware of its era, and its engine typically relies on a few fast cores rather than many threads. The Core Ultra 7 265’s single-core performance is excellent, with a Cinebench R20 single-core score of 884 and a Passmark single-thread score of 4689, but this advantage does not translate into higher frame rates because the GPU becomes the bottleneck at all settings above Low at 1080p.
The nearest CPU rivals in aggregate benchmark scores are the AMD EPYC 4464P (64823, -0.3%), the Intel Core Ultra 7 265F (64438, 0.3%), the AMD EPYC 7343 (64202, 0.7%), and the AMD EPYC 9124 (65104, -0.7%). All of these are within 0.7% of the Core Ultra 7 265’s average score, indicating that the CPU’s performance is typical for a high-end desktop or server part. In Archeage, the CPU’s 20 cores and 30 MB L3 cache are more than sufficient for the game’s demands, and the data shows no evidence of CPU bottlenecks: the frame rates scale purely with resolution and settings, which are GPU-bound variables.
The CPU’s memory support for DDR5 with dual-channel and 102.4 GB/s bandwidth, along with PCIe Gen 5 with 20 lanes, ensures that it does not starve the GPU for data. The integrated Arc Xe-LPG Graphics 32EU is present but irrelevant for this discrete GPU configuration. The launch MSRP of $394 for the CPU reflects its positioning as a high-end part, and its benchmark scores confirm that it is not the limiting factor in this combo. The conclusion from the data is that users who already own this CPU and are considering a GPU upgrade would see substantial gains in Archeage, as the current RX 6600 XT is holding back the system’s potential. Conversely, pairing this CPU with a stronger GPU would likely move the combo rank significantly higher than 2659 out of 3708, given that the CPU has ample headroom for faster graphics cards.
Hardware Specifications
Intel Core Ultra 7 265
AMD Radeon RX 6600 XT
FPS Benchmarks by Resolution & Settings
Performance data for Intel Core Ultra 7 265 + AMD Radeon RX 6600 XT in Archeage
| Resolution | Settings | Avg FPS |
|---|---|---|
| 3840x2160 | Low | 50.0 |
| 3840x2160 | Medium | 44.0 |
| 3840x2160 | High | 30.0 |
| 3840x2160 | Ultra | 20.0 |
| 2560x1440 | Low | 87.0 |
| 2560x1440 | Medium | 77.0 |
| 2560x1440 | High | 52.0 |
| 2560x1440 | Ultra | 36.0 |
| 1920x1080 | Low | 129.0 |
| 1920x1080 | Medium | 114.0 |
| 1920x1080 | High | 78.0 |
| 1920x1080 | Ultra | 53.0 |
Archeage with iUltra 7 265 + Other GPUs
See how Archeage performs with the same CPU but different graphics cards.
Archeage with RX 6600 XT + Other CPUs
See how Archeage performs with the same GPU but different processors.
Other Games with iUltra 7 265 + RX 6600 XT
Explore FPS benchmarks for other games using this same hardware combination.