Fivem

Fivem is a multiplayer modification platform that stresses both the CPU and GPU depending on resolution and settings. This analysis examines the AMD Ryzen 5 5600F paired with the AMD Radeon RX 7600 XT, a 6-core/12-thread Zen 3 processor and a 16 GB RDNA 3.0 graphics card. The data shows a combo that delivers playable frame rates at 1080p and 1440p, but struggles at 4K with higher settings, revealing a clear balance between the two components.

Resolution Scaling

The measured FPS data for this combo shows a steep performance drop as resolution increases, which is typical for a mid-range GPU paired with a capable CPU. At 1080p with Low settings, the combo averages 167 FPS. Moving to 1440p Low drops that to 110 FPS, a 34% reduction. At 4K Low, the average falls further to 61 FPS, which is 63% below the 1080p Low figure. This scaling pattern indicates that the GPU becomes the primary limiting factor as pixel count rises, while the CPU has enough headroom at lower resolutions to push very high frame rates.

With High settings, the resolution scaling is even more pronounced. The combo delivers 106 FPS at 1080p, 69 FPS at 1440p, and only 39 FPS at 4K. The gap between 1080p and 4K here is 67 FPS, or roughly 63% lower. This suggests that High settings introduce additional shading and geometry work that disproportionately taxes the GPU at higher resolutions. The 4K High result of 39 FPS is below the 60 FPS threshold that many users consider smooth, indicating that this resolution/settings combination is not ideal for this hardware.

Ultra settings tell a similar story. At 1080p Ultra, the combo manages 82 FPS. At 1440p Ultra, it drops to 54 FPS, and at 4K Ultra, it falls to 30 FPS. The 4K Ultra result is barely playable for slow-paced content, but it shows that the GPU is fully saturated. The scaling from 1080p to 1440p Ultra is a 34% drop, while from 1440p to 4K Ultra is a 44% drop, indicating that the GPU’s memory bandwidth and processing power are being exhausted at the highest settings.

Medium settings provide the only complete min/max data in the FACT PACK. At 1080p Medium, the average is 132 FPS with a minimum of 112 FPS and maximum of 152 FPS. At 1440p Medium, the average is 87 FPS with a minimum of 74 FPS and maximum of 100 FPS. At 4K Medium, the average is 48 FPS with a minimum of 41 FPS and maximum of 55 FPS. The minimum frame rates at 4K Medium (41 FPS) are still above the 30 FPS floor, but the average of 48 FPS suggests that users will experience noticeable slowdowns in busy multiplayer sessions.

The limiting component at 1080p is likely the CPU in some scenarios, given that the Ryzen 5 5600F has a boost clock of 4.00 GHz and 6 cores. However, the fact that FPS drops by roughly 34-37% when moving from 1080p to 1440p at Low settings (167 to 110 FPS) suggests that the GPU is already becoming a bottleneck even at lower settings. At 4K, the GPU is unequivocally the limiting factor, as the RX 7600 XT’s 128-bit memory bus and 288.0 GB/s bandwidth are insufficient to maintain high frame rates at that pixel count.

CPU Role

The AMD Ryzen 5 5600F is a 6-core, 12-thread processor based on the Zen 3 architecture, codenamed Vermeer. It operates on the AMD Socket AM4 platform with a base clock of 3.00 GHz and a boost clock of 4.00 GHz. The processor has a 32 MB shared L3 cache, which is significant for gaming workloads that benefit from larger cache pools. Its PassMark single-thread score is 2872, and its multithread score is 19236, placing it in the 85th percentile among all CPUs.

In Fivem, which is known for being CPU-intensive in multiplayer scenarios due to script processing and entity management, the Ryzen 5 5600F’s single-thread performance is crucial. The single-thread score of 2872 is solid for a mid-range processor, and the 32 MB L3 cache helps reduce memory latency. The processor’s PassMark physics score is 1043, which is relatively low compared to its other scores, but this may not directly translate to gaming performance.

The CPU’s nearest rivals in terms of average benchmark score include the Intel Core Ultra 5 225 (avg score 36938, deltaPct 0), the AMD Ryzen 5 5500X3D (avg score 37018, deltaPct -0.2), the AMD Ryzen AI 7 PRO 450 (avg score 37093, deltaPct -0.4), and the Intel Core i9-12900T (avg score 37112, deltaPct -0.5). The Ryzen 5 5600F’s average benchmark score is 36945, meaning it sits within 0.5% of these rivals. This indicates that the CPU’s raw compute performance is competitive with those parts, but the Fivem results will depend on how the game utilizes those cores.

At 1080p Low, the combo achieves 167 FPS. This high frame rate suggests that the CPU is not the primary bottleneck at this setting, as the GPU is likely able to keep up with the CPU’s output. However, at 1080p Ultra, the FPS drops to 82, which is a 51% reduction from Low. This drop is more attributable to the GPU’s workload, but the CPU’s 6 cores may also be limiting in scenes with many players or complex scripts. The processor’s 12 threads provide some headroom for background tasks, but Fivem’s server-side code often runs on a single thread, making the 4.00 GHz boost clock more important than core count.

The Ryzen 5 5600F’s memory bandwidth is 51.2 GB/s, which is standard for dual-channel DDR4. This is sufficient for most gaming workloads, but the RX 7600 XT’s 288.0 GB/s bandwidth is far higher, meaning the GPU is not starved for data. The CPU’s PCIe Gen 4 support with 20 lanes (CPU only) ensures that the GPU can communicate at full bandwidth, though the RX 7600 XT uses a PCIe 4.0 x8 interface, which is halved but still adequate for this GPU class.

In terms of CPU-bound scenarios, the data shows that at 1440p Low, the combo hits 110 FPS, which is still high. This suggests that even at 1440p, the CPU is not fully saturated. Only at 4K does the GPU become the clear bottleneck, with FPS dropping to 61 at Low settings. The CPU’s role in Fivem is therefore more about maintaining minimum frame rates in crowded areas, and the 6-core/12-thread configuration with a 4.00 GHz boost is adequate for that purpose.

GPU Role

The AMD Radeon RX 7600 XT is based on the RDNA 3.0 architecture, with the Navi 33 chip codenamed Hotpink Bonefish. It has 16 GB of GDDR6 memory on a 128-bit bus, providing 288.0 GB/s of bandwidth. The GPU’s boost clock is 2755 MHz, with a game clock of 2470 MHz and a base clock of 1980 MHz. It features 2048 shading units, 128 TMUs, and 64 ROPs, with 32 ray tracing cores. The GPU’s FP32 performance is 22.57 TFLOPS, and its pixel rate is 176.3 GPixel/s.

In Fivem, the GPU’s 16 GB VRAM is a notable asset, as the game can use significant memory for textures and assets, especially with high-resolution mods. However, the 128-bit memory bus is a limiting factor, as it restricts memory bandwidth compared to wider-bus GPUs. The 288.0 GB/s bandwidth is adequate for 1080p and 1440p, but at 4K, the GPU struggles to feed its processing units, resulting in lower frame rates.

The GPU’s PassMark G3D score is 17132, and its average benchmark score is 17083, placing it in the 60th percentile among all GPUs. Its nearest rivals include the NVIDIA GeForce GTX 690 (avg score 17037, deltaPct 0.3), the AMD Radeon HD 7970M (avg score 17019, deltaPct 0.4), the NVIDIA GeForce RTX 3070 (avg score 17208, deltaPct -0.7), and the NVIDIA Tesla M4 (avg score 16932, deltaPct 0.9). The RX 7600 XT’s score is within 1% of these rivals, indicating that its raw compute performance is similar to that of the RTX 3070, though the RTX 3070 has a wider memory bus and more bandwidth in practice.

The GPU’s role in Fivem is most evident in the resolution scaling data. At 1080p Low, the combo achieves 167 FPS, which is likely near the CPU’s limit. At 1080p Ultra, the FPS drops to 82, a 51% reduction, showing that the GPU is heavily taxed by higher settings. The 16 GB VRAM is unlikely to be a bottleneck at 1080p, but the GPU’s 2048 shading units are limited when processing complex shaders at Ultra quality.

At 1440p, the GPU’s limitations become more apparent. Low settings yield 110 FPS, which is still smooth, but Ultra settings drop to 54 FPS. The 34% drop from Low to Ultra at 1440p is similar to the 1080p drop, but the absolute numbers are lower, indicating that the GPU is approaching its limits. The 4K results confirm this: even at Low settings, the combo only manages 61 FPS, and at Ultra, it drops to 30 FPS. The 128-bit bus and 288.0 GB/s bandwidth are simply insufficient for 4K gaming in Fivem, especially with the game’s draw distances and multiplayer entity counts.

The GPU’s ray tracing cores (32) are present but not heavily utilized in Fivem, as the game does not have mandatory ray tracing. The 22.57 TFLOPS FP32 performance is decent for rasterization, but the GPU’s 64 ROPs limit fill-rate-bound scenarios. The pixel rate of 176.3 GPixel/s is moderate, and at 4K Ultra, the combo’s 30 FPS average suggests that the ROPs are overwhelmed.

How This Combo Ranks

The AMD Ryzen 5 5600F + AMD Radeon RX 7600 XT combo ranks 1876 out of 3005 tested combos in Fivem. This places it in the 62nd percentile of all tested combinations, meaning roughly 62% of combos perform better in this game. This ranking reflects the GPU’s mid-range position (60th percentile among all GPUs) and the CPU’s solid but not top-tier performance (85th percentile among all CPUs).

The combo’s rank suggests that it is a capable mid-range pairing, but it is not optimized for high-refresh-rate 4K gaming. The CPU’s high percentile (85th) is offset by the GPU’s lower percentile (60th), resulting in an overall rank that is closer to the GPU’s level. This indicates that the GPU is the bottleneck in most scenarios, especially at higher resolutions.

Compared to other combos, this pairing is likely competitive with systems that use similar mid-range GPUs. The RX 7600 XT’s nearest GPU rival, the NVIDIA GeForce RTX 3070, has a slightly higher average benchmark score (17208 vs 17083, deltaPct -0.7), suggesting that an RTX 3070-based combo might rank slightly higher. However, the 16 GB VRAM of the RX 7600 XT could provide an advantage in Fivem modded scenarios that use more than 8 GB of VRAM, though the FACT PACK does not provide VRAM usage data.

The CPU’s nearest rivals are all within 0.5% of its average score, meaning that swapping the Ryzen 5 5600F for an Intel Core i9-12900T or AMD Ryzen 5 5500X3D would likely result in minimal FPS changes. The 5500X3D, with its 3D V-Cache, might have a slight edge in Fivem due to the game’s cache sensitivity, but the data does not provide specific Fivem scores for those CPUs.

The combo rank of 1876 out of 3005 indicates that this is a solid mid-pack performer. Users looking for higher FPS at 4K would need a more powerful GPU, while those targeting 1080p high-refresh-rate gaming might find this combo sufficient, given that it hits 106 FPS at 1080p High and 167 FPS at 1080p Low.

FAQ

Q: What is the best resolution for this combo in Fivem?

A: Based on the measured FPS data, 1080p is the best resolution. At Medium settings, the combo averages 132 FPS with a minimum of 112 FPS. At 1440p Medium, the average drops to 87 FPS, and at 4K Medium, it falls to 48 FPS. For a smooth experience above 60 FPS, 1080p Medium or High (106 FPS) are the most suitable.

Q: Can this combo handle 4K gaming in Fivem?

A: The data shows that 4K is only playable at Low settings, where the combo averages 61 FPS. At Medium settings, the average drops to 48 FPS with a minimum of 41 FPS, and at High settings, it falls to 39 FPS. Ultra settings produce an average of 30 FPS. Users should stick to 4K Low for acceptable performance.

Q: How does the RX 7600 XT compare to its nearest GPU rival, the RTX 3070?

A: The RX 7600 XT has an average benchmark score of 17083, while the RTX 3070 has a score of 17208, a deltaPct of -0.7% relative to the RX 7600 XT. This means the RTX 3070 is slightly faster on average, but the RX 7600 XT has 16 GB of VRAM versus the RTX 3070’s likely smaller capacity, which could matter in Fivem modded scenarios.

Q: Is the Ryzen 5 5600F a bottleneck for the RX 7600 XT?

A: The data suggests that the CPU is not the primary bottleneck at most settings. At 1080p Low, the combo hits 167 FPS, and at 1440p Low, it hits 110 FPS, indicating the GPU is limiting performance. The CPU’s PassMark single-thread score of 2872 and multithread score of 19236 are sufficient for this GPU class.

Q: What settings provide the highest minimum FPS at 1440p?

A: At 1440p Medium, the combo has a minimum FPS of 74 and an average of 87 FPS. This is the only 1440p setting with min/max data in the FACT PACK. For higher minimums, users would need to select Low settings, which average 110 FPS, though no minimum value is provided.

Q: How does this combo rank among all tested combos in Fivem?

A: This combo ranks 1876 out of 3005 tested combos, placing it in the 62nd percentile. This means 62% of combos perform better, but also that 38% perform worse. The rank is influenced by the GPU’s 60th percentile standing among all GPUs.

Measured FPS Breakdown

The measured FPS data for the AMD Ryzen 5 5600F + AMD Radeon RX 7600 XT in Fivem is as follows:

3840x2160 (4K):

• Low settings: 61 FPS average
• Medium settings: 48 FPS average, 41 FPS minimum, 55 FPS maximum
• High settings: 39 FPS average
• Ultra settings: 30 FPS average

2560x1440 (1440p):

• Low settings: 110 FPS average
• Medium settings: 87 FPS average, 74 FPS minimum, 100 FPS maximum
• High settings: 69 FPS average
• Ultra settings: 54 FPS average

1920x1080 (1080p):

• Low settings: 167 FPS average
• Medium settings: 132 FPS average, 112 FPS minimum, 152 FPS maximum
• High settings: 106 FPS average
• Ultra settings: 82 FPS average

These numbers reveal a clear performance hierarchy. At 1080p, the combo delivers playable frame rates across all settings, with even Ultra settings averaging 82 FPS. At 1440p, Low and Medium settings remain smooth (110 and 87 FPS respectively), while High and Ultra drop below 70 FPS. At 4K, only Low settings exceed 60 FPS, and Ultra settings dip to 30 FPS, which is the minimum playable threshold.

The Medium settings data provides the most complete picture, with min/max values at each resolution. At 1080p Medium, the minimum FPS of 112 is above the 60 FPS threshold, indicating consistent performance. At 1440p Medium, the minimum of 74 FPS is still smooth, but at 4K Medium, the minimum of 41 FPS may cause noticeable stutters in busy multiplayer sessions. The gap between minimum and maximum FPS at 4K Medium (41 to 55 FPS) is 14 FPS, which is relatively narrow, suggesting that the GPU is consistently near its limit.

The data also shows that the difference between Low and Ultra settings is significant. At 1080p, the gap is 85 FPS (167 to 82), at 1440p it is 56 FPS (110 to 54), and at 4K it is 31 FPS (61 to 30). This indicates that the GPU’s performance scales poorly with settings at higher resolutions, as the processing demands outpace the 22.57 TFLOPS FP32 performance and 288.0 GB/s bandwidth. Users should prioritize Low or Medium settings at 1440p and above to maintain playable frame rates.