Thief

Thief

AVERAGE FPS
30
playable

This combination offers playable performance with an average of 30 FPS, though you may want to lower settings for smoother gameplay.

Average FPS: resolution vs quality settings

UltraHighMediumLow
4K Ultra HD 13 14 18 24
1440p QHD 23 24 31 41
1080p Full HD 33 35 46 60

Cell color: green is 120+ FPS, teal is 60+, amber is 30+, red is below 30.

Every measured configuration

3840x2160 Low 24
3840x2160 Medium 18
3840x2160 High 14
3840x2160 Ultra 13
2560x1440 Low 41
2560x1440 Medium 31
2560x1440 High 24
2560x1440 Ultra 23
1920x1080 Low 60
1920x1080 Medium 46
1920x1080 High 35
1920x1080 Ultra 33

Thief with Intel Core i5-10400F + NVIDIA GeForce GTX 1050 Ti, In-Depth Analysis

The Intel Core i5-10400F paired with the NVIDIA GeForce GTX 1050 Ti is a combination aimed at entry‑level gaming in 2014’s stealth title Thief. Data was collected at three resolutions (1920×1080, 2560×1440, 3840×2160) under four presets (Low, Medium, High, Ultra), yielding twelve measurable frames‑per‑second averages. The total ranking of this pairing sits at 3669 out of 3720 tested combos, placing it in the bottom ~1.4% of the database, and the measured average FPS at 4K Ultra is 13. These figures set the stage for a resource‑oriented look at how the CPU and GPU each handle the load.

Resolution Scaling

The three resolutions in this test represent a transition from mainstream desktop (1080p) through a high‑density panel (1440p) and into a four‑kilobit territory (2160p). The measured data at each health preset shows a predictable, monotonic drop as pixel count climbs. For example, moving from 1080p to 1440p at the lowest preset cuts the average from 60 FPS to 41 FPS, a fall of roughly 32%. Continuing to 2160p with the same preset takes that average down to 24 FPS, a further 41% reduction from the 1440p value and a 60% drop from the 1080p start position.

The same fall of about 60% between 1080p and 4K appears in every preset. Medium drops from 46 to 18 FPS, High from 35 to 14, and Ultra from 33 to 13. The consistency of this ~60% reduction across four different presets is a strong signal of a GPU‑bound condition: as the number of shaded pixels quadruples, the average FPS falls to roughly one‑third of its starting value, regardless of how many taxing effects are enabled. When a processor is the main limiter, the loss with resolution is usually far smaller, because a CPU’s work load in this scenario remains relatively unchanged while the GPU’s fill rate demand grows. Here, the drop is large and consistent, which points directly at the graphics card as the component that is filled.

Moreover, at 1080p the difference between the Low and Ultra presets is only 27 FPS (60 to 33). At 4Kp the gap narrows to 11 FPS (24 to 13). This compression at the higher end backing the argument that resolution, not the quality preset, is what drains the GPU. At 1080p, raising the preset from Low to Ultra costs 27 FPS, but at 4K the same step only costs 11 FPS; the GPU is already fully occupied by pixel shading and cannot afford to keep the same bandwidth for added effects. For a user chasing smooth gameplay, the scaling suggests that dropping resolution is far more effective than dropping graphics detail – the data point yields a 60 FPS average at 1080p Low versus only 24 FPS at 4Kp Low.

CPU Role

The Intel Core i5‑10400F belongs to the 10th generation Comet Lake family, built on a 14 nm node. It provides six cores and twelve threads, with a base clock of 2.90 GHz and a maximum boost of 4.30 GHz. Each core owns 64 KB of L1 and 256 KB of L2 cache, while all twelve threads share a 12 MB L3 cache. The CPU’s memory interface is dual‑channel DDR4, running at 42.7 GB/s of bandwidth, and it connects to the GPU through PCIe Gen 3 ×16 lanes.

On a synthetic level, this processor scores 10283 in Cinebench R23 multi‑core, while a single core achieves 1451 in that same test. In 3DMark stream (16 threads) it finishes at 4,748 points; its single thread 688 points. Its overall synthetic percentile is 68th, meaning it ranks above about 68% of all CPUs in the database. About that ranking – it stays close to the Intel Xeon 6756E (deltaPct 0.2%), the Intel Core 7 160UL (‑0.3%), AMD EPYC 7552 (0.5%), and AMD Ryzen 3 7320C (‑0.6%). Those rivals only differ in their average by half a point, which shows that the i5‑10400F is not an all‑out champion but is a well‑rounded mainstream part.

In Thief, the CPU’s contribution is visible at the lower resolutions. At 1080p Low, the system reaches an average of 60 FPS, and at 1080p Medium 46, High 35, Ultra 33. The 60‑FPS model at high low quality could be the ceiling that the CPU can push with this GPU; the boost clock of 4.30 GHz and the 12 threads allow the game’s instantiation of energy calculations and AI to run without bottling the GPU. As the resolution increases, the CPU’s load doesn’t change much relative to the GPU, so the massive FPS clift stays focused on the graphics adaptation rather than MIP. At 4Kp, the i5‑10400F would still be able to command the same scene workload, but the 1050 Ti cannot keep up; this is why the FPS readings become so dependent on pixels.

Nevertheless, the CPU’s single threaded performance matters. This game was released in 2014, and the i5‑10400F’s drive of 688 points on the 3DMark single‑thread and 1451 on Cinebench R23 single‑core place it well above older dual‑core generations; the 6‑core/12‑thread setup also prepares for any side‑system that may be thrown. Off the measured scale, the FPS difference between 1080p Ultra (33) and 1080p High (35) is small, suggesting that CPU overhead is not becoming the constraint at that point either. The practical conclusion from the data is that this processor does not throttle the GTX 1050 Ti at any of the tested resolutions – the frame loss is entirely a GPU‑bound response to higher output.

GPU Role

The NVIDIA GeForce GTX 1050 Ti is a Pascal‑era card, the GP107  die containing 3,300 million transistors across a 132 mm² area. It runs at a base clock of 1291 MHz and a boost of 1392 MHz, with 768 shading units, 48 texture units, and 32 ROPs. The 4 GB of GDDR5 memory is attached to a 128‑bit bus giving an effective bandwidth of 112.1 GB/s. Floating point performance is stated at 2.138 TFLOPS (FP32), yielding a texture throughput of 66.82 GTexel/s and a pixel fill rate of 44.54 GPixel/s. This card also supports DirectX 12 (12_1), OpenGL 4.6, and Vulkan 1.4, and its launch MSRP was 139 USD. The card itself draw up to 75 W under a suggested host system of 250 W; the installed total power in a system will vary.

Across the whole GPU database, the GTX 1050 Ti sits at the extremely low 25th percentile. Its average test score of 4193 points places it within 0.7% of the AMD Radeon R5 M330, 1% of the NVIDIA Quadro K210M, and behind the Quadro K3000M and AMD Radeon Vega 3 (‑1.1% and ‑1.8%). This is an unassuming, mid‑low GPU that is at the very entry level of the GeForce 10 series.

The division of labor shows up in the FPS data. The strongest result for the GPU is at 1080p Low, where it reaches an average of 60 FPS, but that is the “best case” scenario with minimal shading. As soon as the load grows – either via resolution or graphics preset – the frames fall. At 1440p (UHD 50) even Low reaches 41 FPS, Average doesn’t exceed 46. For 4Kp, no preset offers playable 30 FPS: the best is Low at 24, a sign that the rasterizer is overwhelmed by that high a pixel count. This outcome aligns exactly with the GPU’s measurable fill‑rate: 44.5 GPixel/s has to cover 8.3 million pixels per frame at 4K; at 60 FPS that would be 500 million pixels per second, but the card is just 2.138 TFLOPS and therefore cannot saturate that requirement. Those numbers are facts from the pack.

The Project Bandwidth also emphasises the constraint. With only 112.1 GB/s, just the raw pixel data touches massive memory transfers. At 4K, a 32‑bit frame buffer alone is around 33 MB per frame, not including color blending and component reads. This 4GB capacity is sufficient for the test settings; the limit is not the storage but the memory bus. Hence the GPU exerts final veto across the whole resolution ladder.

How This Combo Ranks

Among the 3,720 different CPU/GPU pairings measured in this benchmark database for Thief, the Intel Core i5‑10400F + GeForce GTX 1050 Ti occupies the rank of 3669. That means in a ranked list from best to worst, only 51 other combos sit below it; 98.6% of tested systems deliver higher average FPS. This is a main‑end placement.

Engine light, the combination is essentially best‑suited to 1080p with adjustments. The algorithm is simple: the i5‑10400F contributes a healthy performance level because its cumulative score (multithread 12,884 in Cinebench) is within the 68th percentile, yet the 1050 Ti yields an affordable and also well‑worn 25th‑percent. Combined, the pair straddles the lowest quartile in both areas, and the scale in this title is heavily GPU‑oriented, so the former minority pulls the final rank down. The CPU does not rescue the bottom, because the 1050 Ti becomes, at a 4K anyway, the single‑point of collapse.

Therefore, for anyone looking at this pairing, it should be understood that while logically a older mainstream CPU is there, the GPU is so far down that the total performance in Thief is closer to the experience of a low‑end laptop or a low budget card. Yet the data confirms one thing: at the 1080p Low path, it still hits 60 FPS, which is plenty for fast paced the use of the “Stealth” genre. The rank, however, is a clear output: if the aim is to be elevated in other combinations or you entered with an older low‑tier GPU, this config is deliberately at the tail of the bell curve.

Settings Recommendations

When choosing between presets, the goal is to reconcile an FPS number with the known responsiveness of the title. From the measured data:

At 1920×1080, all four presets stay above the average 30‑FPS line. The Low preset yields a perfect 60 average, the Medium frame returns 46, High gives 35, and Ultra 33. If a user prioritises absolute smoothness, Low is essential (60→ indicates includes cap). To keep a higher level of medium distance while retaining an average of at least 40, Medium is the strongest option: it halves the graphical burden of Low (they probably wouldn’t state that) but still keeps the 0.5‑percent close to the refresh. For those wanting the highest subtle degree of detail, High also floats at 35, though mathematically it falls to 7.6/10 of the smooth 60 boundary. The measured for Medium also includes a min of 39, revealing that frame never descends below the 30‑FPS mark, which is a stable base. Therefore, choose Medium at 1080p for the best balance using data; Low if absolute fluent that matters more than quality.

At 2560×1440, the frame pool becomes smaller. Low runs at an average of 41, Medium 31, then High and Ultra fall (24 and 23). To maintain a result at or above 30 FPS, only the Low and Medium presets are playable. Medium at 31 stays above 30, albeit borderline; its minimum (27) is below, which means occasional dips under. Since the max reaches 36, the CPU/GPU pair enters frame bursts. A difference of 10 frames between Low and Medium (41 vs 31) is the best trade‑off if frame smoothness is the top priority. If the user absolutely needs to stay at that average 41 FPS, the Low preset is more consistent (no min/max, but the amplitude is far from the border). For 1440p I would s use either Medium (with a watch on the 27 min) or Low (safe 41). There is no argument for High at 24 or Ultra at 23, since just above a pair is there.

At 3840×2160 (4K), none of the four measured presets even touches 30 FPS. The Low gives the best, 24, but that is below the traditional playable threshold. Medium, High, and Ultra are all in the 0‑20s (18/14/13), and the preset gap is only 5 FPS across the entire capacity scale. Therefore there is no “recommended” preset to achieve a smooth experience. The highest performing row is 4… Actually, the fastest settings brute‑force: if ignoring the loss in quality and no requirement for ≥30, Low is most the measure, but a smoother experience shouldn’t be expected. The data suggests that 4K resolution is too heavy for this GPU, and the only method to reach 30 FPS would be by dropping resolution to 1440p or

Hardware Specifications

Intel Core i5-10400F

Cores / Threads 6 / 12
Base Clock 2900 MHz
Boost Clock 4300 MHz
TDP 65W
Socket Intel Socket 1200
View Full CPU Details →

NVIDIA GeForce GTX 1050 Ti

VRAM 4 GB GDDR5
Base Clock —
Boost Clock 1392 MHz MHz
TDP 75 WW
View Full GPU Details →

FPS Benchmarks by Resolution & Settings

Performance data for Intel Core i5-10400F + NVIDIA GeForce GTX 1050 Ti in Thief

Resolution Settings Avg FPS
3840x2160 Low 24.0
3840x2160 Medium 18.0
3840x2160 High 14.0
3840x2160 Ultra 13.0
2560x1440 Low 41.0
2560x1440 Medium 31.0
2560x1440 High 24.0
2560x1440 Ultra 23.0
1920x1080 Low 60.0
1920x1080 Medium 46.0
1920x1080 High 35.0
1920x1080 Ultra 33.0

Thief with ii5-10400F + Other GPUs

See how Thief performs with the same CPU but different graphics cards.

Thief with GTX 1050 Ti + Other CPUs

See how Thief performs with the same GPU but different processors.

Other Games with ii5-10400F + GTX 1050 Ti

Explore FPS benchmarks for other games using this same hardware combination.