Steamworld Build
This combination delivers exceptional performance with an average of 140 FPS, perfect for high refresh rate gaming and competitive play.
Average FPS: resolution vs quality settings
| Ultra | High | Medium | Low | |
|---|---|---|---|---|
| 4K Ultra HD | 43 | 60 | 78 | 103 |
| 1440p QHD | 78 | 116 | 152 | 200 |
| 1080p Full HD | 120 | 179 | 240 | 307 |
Cell color: green is 120+ FPS, teal is 60+, amber is 30+, red is below 30.
Steamworld Build with Intel Core i3-12100F + NVIDIA GeForce RTX 3080 Ti, In-Depth Analysis
Steamworld Build places a relatively light load on modern hardware, and the measured results for the Intel Core i3-12100F paired with the NVIDIA GeForce RTX 3080 Ti confirm this. The data shows a configuration that is heavily GPU-limited at higher resolutions but capable of delivering very high frame rates at 1080p. The following analysis breaks down how this specific combination behaves across the game’s four presets and three resolutions, using only the measured FPS values and the hardware’s benchmark profile.
Resolution Scaling
The frame rate drop from 1080p to 4K is steep and consistent across all settings, which points to the GPU becoming the primary constraint as pixel count rises. At High settings, the average FPS falls from 179.4 at 1920x1080 to 116.1 at 2560x1440, then further to 60.2 at 3840x2160. That represents a 35% reduction from 1080p to 1440p, and another 48% reduction from 1440p to 4K. The pattern is similar for Ultra settings, where the game drops from 119.5 FPS at 1080p to 78.2 at 1440p and then to 42.6 at 4K.
The scaling behavior indicates that the RTX 3080 Ti is the limiting component at 4K for all presets. Even at Low settings, which should minimize GPU work, the 4K result of 102.7 FPS is far below the 307.4 FPS achieved at 1080p. This is a 67% performance loss from the lowest to the highest resolution, a figure that cannot be explained by CPU limitations alone. The i3-12100F, with its 4 cores and 8 threads, shows strong single-thread performance in synthetic tests — a Geekbench single-core score of 2224 and a Cinebench R23 single-core score of 1681 — which suggests it has enough headroom for lower-resolution tasks.
However, at 1080p Low, the 307.4 FPS result is likely approaching the CPU’s limit for this game. The delta between 1080p Low and 1440p Low is a significant 107.5 FPS, but the gap between 1440p Low (199.9 FPS) and 4K Low (102.7 FPS) is also large. The data shows that resolution scaling is not linear; the biggest absolute drops occur when moving from 1440p to 4K, which is expected given that 4K has 2.25 times the pixels of 1440p. For a city builder where camera pans and zoom levels change constantly, this means players with 4K displays will need to make deliberate preset choices to maintain smooth gameplay.
Settings Recommendations
The measured rows provide a clear picture of how each preset balances frame rate against visual quality. At 1920x1080, all four presets are playable, with Low hitting 307.4 FPS, Medium at 239.8 FPS, High at 179.4 FPS, and Ultra at 119.5 FPS. The jump from Medium to High costs 60.4 FPS, while the jump from High to Ultra costs another 59.9 FPS. This suggests that High is the sweet spot for 1080p, offering a frame rate well above 144 Hz displays while avoiding the steep cost of Ultra.
At 2560x1440, the story changes slightly. Medium delivers 151.7 FPS, which is excellent for high-refresh-rate gaming. High drops to 116.1 FPS, still smooth for most monitors, but Ultra falls to 78.2 FPS, which is borderline for 144 Hz panels. The data indicates that Medium is the best experience at 1440p for users prioritizing frame rate, while High is acceptable for those who want better visuals without sacrificing too much responsiveness. Low at 199.9 FPS is unnecessary unless the user has a 240 Hz display and wants maximum headroom.
At 3840x2160, the recommendations shift dramatically. Ultra is barely playable at 42.6 FPS, which is below the 60 FPS threshold for smooth gameplay. High hits 60.2 FPS, just making the cut, while Medium reaches 78 FPS and Low goes up to 102.7 FPS. For 4K, the data strongly favors Medium as the best balance, as it provides a 30% improvement over High while still looking substantially better than Low. High is only recommended for users who accept 60 FPS as a hard cap, and Ultra should be avoided entirely for this combination.
GPU Role
The NVIDIA GeForce RTX 3080 Ti is the dominant component in this pairing, and its specifications explain the 4K performance ceiling. With 12 GB of GDDR6X memory on a 384-bit bus, the card offers 912.4 GB/s of bandwidth, which is ample for a city builder’s texture streaming needs. The GPU’s boost clock of 1665 MHz and base clock of 1365 MHz are modest for a high-end card, but the 10,240 shading units and 112 ROPs provide substantial raw throughput. The synthetic benchmarks reflect this: a PassMark G3D score of 26896 places the card in the 83rd percentile of all GPUs, and it sits within 1.6% of the NVIDIA Tesla M40 in the nearest rival list.
The VRAM capacity is not a limiting factor in these measurements. Steamworld Build’s Low preset at 4K still achieves 102.7 FPS, which indicates that even at lower settings the GPU is not starved for memory. The 12 GB frame buffer is more than sufficient for the game’s assets, and the measured data shows no signs of texture thrashing or memory-related stutters. The GPU’s role becomes clearer when comparing presets: moving from Low to Ultra at 4K costs 60.1 FPS (from 102.7 to 42.6), a 59% reduction that tracks closely with the increased shading and post-processing load. The RTX 3080 Ti’s 34.10 TFLOPS of FP32 compute is the likely driver of this scaling, as higher presets demand more pixel shading work.
Interestingly, the GPU’s nearest rival, the RTX 3090, has an average benchmark score just 0.5% higher, yet the measured in-game results show this 3080 Ti configuration achieving 60.2 FPS at 4K High — a playable result that many less powerful cards cannot reach. The card’s 83rd percentile ranking among all GPUs confirms it is a top-tier product, even if it is not the absolute fastest. For this game, the GPU is clearly the bottleneck at 1440p and 4K, while the CPU becomes more relevant only at 1080p Low.
FAQ
Q: What is the best resolution for this CPU/GPU combo to maintain 60+ FPS at maximum settings?
A: At 1920x1080 with Ultra settings, the combo achieves 119.5 FPS. At 2560x1440 Ultra, it drops to 78.2 FPS. At 3840x2160 Ultra, it falls to 42.6 FPS, which is below 60 FPS.
Q: How much performance is lost when moving from 1080p to 4K at High settings?
A: At High settings, the average FPS goes from 179.4 at 1920x1080 to 60.2 at 3840x2160, a reduction of 119.2 FPS, or roughly 66%.
Q: Is the RTX 3080 Ti’s 12 GB VRAM sufficient for this game?
A: Yes. The measured data shows playable frame rates at all resolutions and presets, with no evidence of memory limitations. The 12 GB GDDR6X memory and 912.4 GB/s bandwidth are more than adequate for Steamworld Build’s requirements.
Q: Does the i3-12100F bottleneck the RTX 3080 Ti in this game?
A: The data suggests minimal bottlenecking. At 1080p Low, the combo reaches 307.4 FPS, which is very high. However, the 4-core processor’s synthetic scores (Cinebench R23 multi-core of 11912) indicate it may cap frame rates in less demanding scenes, though the measured numbers do not show a severe limitation.
Q: What is the frame rate difference between Medium and High at 1440p?
A: At 2560x1440, Medium delivers 151.7 FPS while High delivers 116.1 FPS, a difference of 35.6 FPS. This makes Medium the better choice for high-refresh-rate displays.
Q: How does this combo’s in-game performance compare to its synthetic benchmark ranking?
A: The GPU ranks in the 83rd percentile of all GPUs with an average benchmark score of 41224, and the CPU ranks in the 72nd percentile with an average score of 13516. In-game, the combo achieves 60+ FPS at 4K High, which aligns with the high synthetic rankings.
CPU Role
The Intel Core i3-12100F is a 4-core, 8-thread processor based on the Alder Lake architecture, with a base clock of 3.30 GHz and a boost clock of 4.30 GHz. Its synthetic benchmark results are strong for a budget chip: a Cinebench R23 multi-core score of 11912 and a single-core score of 1681, alongside a Geekbench single-core score of 2224. The processor’s 12 MB of shared L3 cache and 1.25 MB per-core L2 cache provide adequate data locality for a city builder’s simulation logic, which often relies on pathfinding and resource management calculations.
In Steamworld Build, the CPU’s role is most apparent at 1080p with lower settings. At 1920x1080 Low, the combo hits 307.4 FPS, which is so high that the CPU is likely the limiting factor. The 3DMark 4-thread score of 2859 and 8-thread score of 4026 suggest that the processor’s four physical cores are well-utilized, but the game may not scale beyond 8 threads effectively. The CPU’s percentile rank of 72 places it above average, and its nearest rival, the Intel Core i7-7700K, has a delta of only 1.8%, meaning the i3-12100F performs nearly identically to that older flagship in general benchmarks.
However, the measured FPS data shows that the CPU does not bottleneck the GPU in most scenarios. At 1440p High, the combo achieves 116.1 FPS, which is still very high and suggests the GPU is doing the heavy lifting. Only at 1080p Low does the CPU potentially cap performance, as the 307.4 FPS result is above what most games can sustain with a 4-core processor. The 58 W TDP and dual-channel memory support (DDR4 or DDR5) make this a modest power draw, but the benchmark scores indicate it is capable of feeding the RTX 3080 Ti in this specific game without issue.
Measured FPS Breakdown
The full set of measured FPS values provides a complete picture of this combination’s performance. At 1920x1080, the results are: Low at 307.4 FPS, Medium at 239.8 FPS, High at 179.4 FPS, and Ultra at 119.5 FPS. The gap between Low and Ultra is 187.9 FPS, showing that the preset choice has a massive impact at this resolution. At 2560x1440, the values are: Low at 199.9 FPS, Medium at 151.7 FPS, High at 116.1 FPS, and Ultra at 78.2 FPS. The drop from 1080p to 1440p averages about 40% across presets, which is consistent with the pixel count increase.
At 3840x2160, the results become more constrained: Low at 102.7 FPS, Medium at 78 FPS, High at 60.2 FPS, and Ultra at 42.6 FPS. The 4K results show that only Low and Medium exceed 60 FPS, with High just barely crossing the threshold. The Ultra preset at 4K is the only configuration that falls below 45 FPS, making it unsuitable for smooth gameplay. Across all resolutions, the Medium preset offers the most consistent frame rates relative to visual quality, as it stays above 78 FPS even at 4K. The data confirms that this combo is overkill for 1080p (where even Ultra exceeds 100 FPS) and adequate for 1440p, but requires preset compromises at 4K.
Hardware Specifications
Intel Core i3-12100F
NVIDIA GeForce RTX 3080 Ti
FPS Benchmarks by Resolution & Settings
Performance data for Intel Core i3-12100F + NVIDIA GeForce RTX 3080 Ti in Steamworld Build
| Resolution | Settings | Avg FPS |
|---|---|---|
| 3840x2160 | Low | 102.7 |
| 3840x2160 | Medium | 78.0 |
| 3840x2160 | High | 60.2 |
| 3840x2160 | Ultra | 42.6 |
| 2560x1440 | Low | 199.9 |
| 2560x1440 | Medium | 151.7 |
| 2560x1440 | High | 116.1 |
| 2560x1440 | Ultra | 78.2 |
| 1920x1080 | Low | 307.4 |
| 1920x1080 | Medium | 239.8 |
| 1920x1080 | High | 179.4 |
| 1920x1080 | Ultra | 119.5 |
Steamworld Build with ii3-12100F + Other GPUs
See how Steamworld Build performs with the same CPU but different graphics cards.
Steamworld Build with RTX 3080 Ti + Other CPUs
See how Steamworld Build performs with the same GPU but different processors.
Other Games with ii3-12100F + RTX 3080 Ti
Explore FPS benchmarks for other games using this same hardware combination.