Palworld
This combination provides smooth gameplay with an average of 76 FPS, suitable for most gaming scenarios.
Average FPS: resolution vs quality settings
| Ultra | High | Medium | Low | |
|---|---|---|---|---|
| 4K Ultra HD | 27 | 35 | 46 | 57 |
| 1440p QHD | 48 | 64 | 83 | 103 |
| 1080p Full HD | 74 | 97 | 126 | 156 |
Cell color: green is 120+ FPS, teal is 60+, amber is 30+, red is below 30.
Palworld with AMD Ryzen AI Max+ 395 + NVIDIA GeForce RTX 5060 Mobile, In-Depth Analysis
Palworld on a mobile platform is an interesting stress case: a survival game with dense creature and base simulation paired with a mobile CPU-GPU pairing that, on paper at least, punches far above its power class. The pairing here is the AMD Ryzen AI Max+ 395, a 16-core Zen 5 processor in the 95th percentile of all CPUs in the database, and the NVIDIA GeForce RTX 5060 Mobile, a Blackwell 2.0 part sitting in the 67th percentile of all GPUs. Measured results span 1920x1080 through 3840x2160 at four presets, and the data tells a coherent story about where the frame rate ceiling actually lies.
Resolution Scaling
The scaling data is strikingly linear, and that linearity is itself diagnostic. At the Low preset, average frame rates run 156 FPS at 1920x1080, 103 FPS at 2560x1440, and 57 FPS at 3840x2160. Moving from 1080p to 1440p costs roughly a third of the frame rate; moving from 1440p to 4K costs a bit under half again. That near-proportional drop with pixel count is the classic signature of a GPU-limited configuration: when frames scale down almost in lockstep with resolution, the graphics side is the binding constraint, not the CPU.
The Medium preset follows the same pattern: 126 FPS at 1080p, 83 FPS at 1440p, 46 FPS at 4K. High drops from 97 to 64 to 35. Ultra falls from 74 to 48 to 27. In every case, the ratio between adjacent resolutions is consistent, with no plateau at the low end. If the Ryzen AI Max+ 395 were the limiter, 1080p numbers would flatten against the 1440p results — the CPU would put a ceiling on frame rate that no resolution reduction could push past. That flattening does not appear anywhere in this dataset. Even at 1080p Low, where CPU limits typically reveal themselves first, the 156 FPS result sits comfortably within the GPU's scaling curve.
That raises a question worth asking: is the RTX 5060 Mobile leaving performance on the table because the CPU is slow? Almost certainly not. A chip that scores 2044 in Cinebench R23 single-core and ranks in the 95th percentile of all CPUs is not a single-thread bottleneck for a survival title. The data implies the pairing is well balanced in the sense that the GPU is saturated and the CPU has headroom — whether that headroom is wasted or merely idle is a question of expectations.
How This Combo Ranks
Within Palworld specifically, this CPU-GPU combination ranks 2462 out of 3711 tested combos in the database. That places it in the bottom half — a somewhat counterintuitive result given the hardware's individual credentials, and worth unpacking.
The CPU side is elite. The Ryzen AI Max+ 395's average benchmark score of 77740 puts it within 1.6 percent of the AMD Ryzen Threadripper PRO 9945WX and the AMD EPYC Embedded 8224P, 2 percent ahead of the AMD Ryzen 9 8945HX, and only 1.7 percent behind the Intel Core i9-14900K. This is workstation-adjacent compute in a mobile power envelope. Against that backdrop, the combo's middling Palworld rank reflects the GPU, not the processor.
The RTX 5060 Mobile's average benchmark score of 22435 places it 0.5 percent behind the AMD Radeon RX 7700 XT, 1.2 percent ahead of the AMD Radeon RX 5700, 1.3 percent ahead of the AMD Radeon RX 6700S, and 1.3 percent behind the NVIDIA GeForce RTX 4060 Mobile. In other words, the GPU occupies the upper-middle of the pack overall — 67th percentile against all GPUs — but Palworld's leaderboard is populated heavily by desktop-class graphics hardware, which drags this combo's rank down. The rank is a statement about the competition, not a condemnation of the hardware. What the ranking does confirm is that in a game where the GPU is the limiting component, the combo rank tracks the GPU's relative standing almost exactly.
GPU Role
The RTX 5060 Mobile is a 5 nm TSMC part, codename GB206, with 3328 shading units, 104 TMUs, 48 ROPs, 26 RT cores, and 104 tensor cores on a 181 mm² die carrying 21,900 million transistors at a density of 121.0M per mm². Its theoretical throughput figures — 9.684 TFLOPS FP32, a pixel rate of 69.84 GPixel/s, and a texture rate of 151.3 GTexel/s — frame the measured Palworld numbers well.
Consider the pixel rate. At 3840x2160, the display demands roughly 8.3 million pixels per frame; at 35 FPS on the High preset, the GPU is pushing about 291 million pixels per second — a small fraction of the theoretical 69.84 GPixel/s, which is expected, since real games never approach raw fill-rate limits. The more telling spec is memory. The card carries 8 GB of GDDR7 on a 128-bit bus, with memory running at 1500 MHz (24 Gbps effective) for 384.0 GB/s of bandwidth. Eight gigabytes is workable for a stylized survival title, and the measured results bear that out: frame rates fall smoothly as settings rise, with no cliff-edge collapse that would suggest VRAM saturation at 4K. The 27 FPS at 4K Ultra is low, but it is a graceful low, not a catastrophic one.
Clock behavior matters too. The GPU's base clock is 952 MHz with a boost of 1455 MHz, and its 45 W TDP constrains sustained frequencies in a way desktop cards do not face. The consistent resolution scaling across all four presets suggests clocks held stable through the runs; thermally induced clock droop would typically show up as compressed results at the highest settings, and no such compression is visible.
Synthetic results corroborate the gaming picture. The card scores 3013.5 in 3DMark Steel Nomad (DX12), 96969 in Geekbench OpenCL, 96451 in Geekbench Vulkan, and 18852 in PassMark G3D. Palworld is a DirectX 12-era title, and the Steel Nomad result in particular aligns with the upper-mainstream positioning the gaming data implies.
Measured FPS Breakdown
The full measured grid, resolution by resolution:
1920x1080. Low averages 156 FPS. Medium averages 126 FPS, with a recorded range of 107 minimum to 145 maximum — the only rows with min/max data, and notably tight: the floor sits only about 15 percent below the average, indicating frame delivery that is stable rather than spiky. High averages 97 FPS. Ultra averages 74 FPS. Every 1080p preset clears 60 FPS, and three of four clear or approach triple digits.
2560x1440. Low averages 103 FPS. Medium averages 83 FPS with a range of 71 to 96 — again a tight spread, the minimum about 14 percent below the average. High averages 64 FPS. Ultra averages 48 FPS, the first sub-60 result in the dataset. At 1440p, three of the four presets remain at or above 60, with Ultra the lone exception.
3840x2160. Low averages 57 FPS, Medium 46 FPS, High 35 FPS, Ultra 27 FPS. Nothing at native 4K reaches 60, and only the Low preset gets close. The step from Low to Ultra at 4K spans 30 FPS — a 47 percent loss going from the cheapest preset to the most expensive.
Across the board, each preset increment costs roughly 15 to 25 percent of the frame rate, and each resolution step costs a similar fraction. The min/max data available at Medium is the most reassuring signal in the whole dataset: at 1440p Medium, the worst recorded frame is 71 FPS, which still exceeds the 1440p High average.
FAQ
Q: Can this combo run Palworld at 60 FPS?
A: Yes, at multiple configurations. 1080p delivers 60-plus FPS at every preset including Ultra (74 FPS). At 1440p, Low (103), Medium (83), and High (64) all clear the bar; Ultra at 48 does not. At 4K, no preset reaches 60 — the best is Low at 57 FPS.
Q: What is the single fastest measured configuration?
A: 1920x1080 at Low settings, averaging 156 FPS. The slowest is 3840x2160 at Ultra, averaging 27 FPS — a gap of 129 FPS between the extremes of the tested grid.
Q: Is frame delivery stable, or spiky?
A: The measured min/max data, available at the Medium preset, indicates stability. At 1080p Medium the range is 107 to 145 around a 126 average; at 1440p it is 71 to 96 around an 83 average; at 4K it is 39 to 53 around a 46 average. In each case the minimum sits roughly 14 to 15 percent below the average.
Q: Does the CPU hold this pairing back in Palworld?
A: The data says no. Frame rates scale nearly proportionally with resolution at every preset, which is the signature of GPU limitation. The Ryzen AI Max+ 395 sits in the 95th percentile of all CPUs and trades blows with the Intel Core i9-14900K within 1.7 percent — it is not the constraint.
Q: How does the GPU compare to its nearest rivals on aggregate benchmarks?
A: Its average score of 22435 lands within 1.3 percent of four rivals: the AMD Radeon RX 7700 XT (-0.5 percent), the AMD Radeon RX 5700 (+1.2 percent), the AMD Radeon RX 6700S (+1.3 percent), and the NVIDIA GeForce RTX 4060 Mobile (-1.3 percent).
Q: Is 4K viable at all?
A: Only marginally. At Low settings the combo averages 57 FPS — close to but short of 60 — and every other 4K preset falls well below playable thresholds for a fast-paced survival game.
CPU Role
The Ryzen AI Max+ 395 is an unusual chip, and its role in this result set deserves scrutiny. It is a Zen 5 design, codename Strix Halo, built on TSMC's 4 nm node across two dies of 70.6 mm² each, with 16 cores and 32 threads, a 3.00 GHz base clock, and a 5.10 GHz boost. Cache allocation is generous: 80 KB of L1 and 1 MB of L2 per core, with a shared 64 MB L3. Memory support is LPDDR5X over a quad-channel bus delivering 256.0 GB/s of bandwidth, and the platform even supports ECC. The chip integrates Radeon 8060S graphics, uses Socket FP11, and launched as an active mobile-segment product.
Its benchmark résumé backs the gaming data's implication of abundant headroom. Cinebench R23 multi-core lands at 35314 with a 2044 single-core score; Cinebench R15 posts 5463 multi and 316 single; Geekbench records 20992 multi and 2464 single. PassMark multithread reaches 54934, single-thread 4147, physics 3481, and integer math 200665. Against all CPUs in the database it ranks in the 95th percentile, sitting 1.6 percent from the Threadripper PRO 9945WX and EPYC Embedded 8224P, 2 percent ahead of the Ryzen 9 8945HX, and 1.7 percent behind the Core i9-14900K — a desktop flagship.
For Palworld specifically, none of this muscle is the deciding factor. A survival game with base-building and creature AI does exercise multiple threads, and the 16-core/32-thread configuration with 64 MB of shared L3 ensures the simulation side never starves the render thread. The 5.10 GHz boost clock keeps single-threaded game logic — pathing, physics, interaction — well fed. But because the GPU saturates first at every tested resolution and preset, the CPU's contribution shows up as stability rather than headline frame rate: the tight min/max spreads at the Medium preset (107–145 FPS at 1080p, 71–96 at 1440p) are consistent with a processor that never falters under load. The interesting corollary: this CPU could drive a substantially faster GPU in Palworld before the balance flipped. Pairing it with the RTX 5060 Mobile means the CPU's 95th-percentile capability is largely dormant in this title.
Settings Recommendations
The measured grid supports clear guidance. At 1920x1080, Ultra is the pick — 74 FPS average with the next preset down at 97 means there is no meaningful penalty for maximum fidelity, and the CPU's headroom guarantees the frame delivery stays smooth. For 1440p, High is the sweet spot: 64 FPS average keeps the experience above 60, and the Medium row's 71 FPS minimum suggests the High preset's frame floor is likely tolerable. Players sensitive to dips could step to Medium, where the measured minimum of 71 FPS provides substantial cushion.
At 3840x2160, the honest recommendation is to avoid native 4K, or to accept Low settings at 57 FPS as the ceiling of what this hardware delivers — a compromise that sacrifices visual richness in a game whose stylized art direction is relatively forgiving of lower presets. Between Low (57) and Medium (46) at 4K, the 11 FPS difference matters more than the visual delta in a survival title where reaction time matters during creature encounters.
The broader verdict from the data: this is a 1080p-max or 1440p-high configuration for Palworld, GPU-limited at every point, held back by nothing on the processor side, and ranked mid-pack among tested combos purely because the graphics hardware — competitive though it is against its own mobile-and-desktop rival cohort — defines the ceiling.
Hardware Specifications
AMD Ryzen AI Max+ 395
NVIDIA GeForce RTX 5060 Mobile
FPS Benchmarks by Resolution & Settings
Performance data for AMD Ryzen AI Max+ 395 + NVIDIA GeForce RTX 5060 Mobile in Palworld
| Resolution | Settings | Avg FPS |
|---|---|---|
| 3840x2160 | Low | 57.0 |
| 3840x2160 | Medium | 46.0 |
| 3840x2160 | High | 35.0 |
| 3840x2160 | Ultra | 27.0 |
| 2560x1440 | Low | 103.0 |
| 2560x1440 | Medium | 83.0 |
| 2560x1440 | High | 64.0 |
| 2560x1440 | Ultra | 48.0 |
| 1920x1080 | Low | 156.0 |
| 1920x1080 | Medium | 126.0 |
| 1920x1080 | High | 97.0 |
| 1920x1080 | Ultra | 74.0 |
Palworld with RTX 5060 Mobile + Other CPUs
See how Palworld performs with the same GPU but different processors.
Other Games with Ryzen AI Max+ 395 + RTX 5060 Mobile
Explore FPS benchmarks for other games using this same hardware combination.