Intel Core i7-2710QE vs Intel Pentium Gold G5400 Comparison

Intel
INTEL

Intel Core i7-2710QE

CORE STATE Sandy Bridge
CORE SPECS 4 Cores / 8 Threads
CLOCK SPEED 2.1 Base / 3 GHz Turbo
CACHE 6 MB (shared)
MAX TDP 45W
ARCHITECTURE Sandy Bridge
nm
PROCESS 32 nm
LAUNCH DATE 2011
VS
Intel
INTEL

Pentium Gold G5400

CORE STATE Coffee Lake
CORE SPECS 2 Cores / 4 Threads
CLOCK SPEED 3.7 Base
CACHE 4 MB (shared)
MAX TDP 58W
ARCHITECTURE Coffee Lake
nm
PROCESS 14 nm
LAUNCH DATE 2018

PERFORMANCE BENCHMARKS

cinebench_cinebench_r15_multicore
321
319
cinebench_cinebench_r20_multicore
1,338
1,331
cinebench_cinebench_r20_singlecore
188
187
cinebench_cinebench_r23_multicore
3,186
3,171
cinebench_cinebench_r23_singlecore
449
447

Analysis: Intel Core i7-2710QE vs Intel Pentium Gold G5400

The Intel Pentium Gold G5400 and Intel Core i7-2710QE are two very different processors from different eras, yet benchmark results place them in a remarkably close contest. The G5400 is a modern dual-core desktop part built on a 14 nm process, while the i7-2710QE is a quad-core mobile chip from 2011 on a 32 nm node. Despite the generational gap, the data shows the i7-2710QE edges out the G5400 in every single recorded benchmark, though by margins so slim they are nearly negligible. The average benchmark scores tell the same story: the G5400 scores 1091, while the i7-2710QE scores 1096, a difference of just 0.5%. Both processors sit in the 30th and 31st percentiles of all CPUs respectively, indicating they occupy nearly identical performance tiers.

Head-to-Head Benchmarks

The head-to-head results are striking for their consistency. Across five Cinebench tests, the Intel Core i7-2710QE wins every single one, but the largest margin of victory is a mere 0.6%. In the Cinebench R15 multicore test, the G5400 scores 319 against the i7-2710QE’s 321, a delta of -0.6%. That is a difference of two points, which is within any reasonable margin of error for a benchmark run. The story repeats in Cinebench R20 multicore, where the G5400 posts 1331 and the i7-2710QE posts 1338, a 0.5% gap. Single-core performance is equally tight: in Cinebench R20 single-core, the G5400 scores 187, while the i7-2710QE scores 188, another 0.5% edge for the older chip.

The most recent benchmark, Cinebench R23, shows the same pattern. In multicore, the G5400 scores 3171 and the i7-2710QE scores 3186, a 0.5% difference. In single-core, the gap narrows further to 0.4%, with scores of 447 and 449 respectively. These are not the kind of results where one processor demonstrates a clear architectural superiority. Instead, the data indicates that the i7-2710QE’s two additional physical cores and four additional threads are almost exactly offset by the G5400’s higher clock speed and newer architecture. The G5400 runs at a base clock of 3.70 GHz with no boost, while the i7-2710QE has a base clock of 2.10 GHz and a boost clock of 3.00 GHz. That raw frequency advantage for the Pentium Gold appears to neutralize the core-count advantage of the Core i7 in these workloads.

Looking at the nearest rivals for each chip provides additional context. The G5400’s average score of 1091 puts it exactly level with the Intel Core i5-3475S, which also scores 1091. It is 0.1% behind the Intel Core i7-10510Y and Intel Core i7-4600M, both scoring 1092 and 1093 respectively, and 0.2% ahead of the AMD Athlon 220GE at 1088. The i7-2710QE’s average of 1096 matches the Intel Core i7-2670QM exactly, sits 0.1% ahead of the Intel Core i5-3470S at 1095, and is 0.1% behind the AMD PRO A10-8850B at 1098. These rival charts confirm that both CPUs are essentially interchangeable in terms of raw compute performance, with the i7-2710QE holding a razor-thin overall edge.

The Verdict

The data paints a clear picture: there is no meaningful performance winner between these two processors. The Intel Core i7-2710QE wins all five head-to-head benchmarks, but the largest delta is 0.6%, and the average benchmark score difference is only 5 points out of roughly 1090. For anyone choosing based purely on the numbers in this benchmark database, the decision comes down to platform and features rather than raw speed. The G5400 is a desktop part on Intel Socket 1151 with a launch MSRP of $64, while the i7-2710QE is a mobile part on Intel Socket G2 (988B) with no listed launch MSRP.

If the use case is a desktop build, the G5400 is the logical choice simply because it fits a modern mainstream socket. It supports DDR4 memory and PCIe Gen 3 with 16 lanes from the CPU, and it includes UHD Graphics 610. The i7-2710QE, being a mobile chip, is not designed for desktop motherboards and uses the older Socket G2 (988B). Its integrated graphics are Intel HD 3000, and it lacks the memory bandwidth specification that the G5400 provides at 38.4 GB/s. For a mobile platform where the i7-2710QE is already installed, there is no reason to swap it out for a G5400 based on performance, since the scores are effectively identical. Conversely, for a new desktop build, the G5400 is the only one of the two that is realistically usable in a modern system.

The production status for both is end-of-life, so neither is a forward-looking purchase. The G5400 was released in April 2018, while the i7-2710QE dates back to January 2011. That seven-year gap explains the process node difference (14 nm versus 32 nm) and the transistor count disparity (the i7-2710QE has 1,160 million transistors on a 216 mm² die, while the G5400 has no listed transistor count but a 126 mm² die). The newer process allows the G5400 to achieve higher clock speeds at a higher TDP of 58 watts, versus 45 watts for the i7-2710QE. The verdict is simple: pick the G5400 for a desktop, pick the i7-2710QE only if the platform dictates it.

Architecture Differences

The architectural gap between these two processors is substantial, even if the benchmark results are not. The G5400 is built on Coffee Lake, a 14 nm architecture that Intel used across its 8th and 9th generation desktop processors. It features 2 cores and 4 threads, with a base clock of 3.70 GHz and no boost capability. The i7-2710QE is based on Sandy Bridge, a 32 nm architecture from 2011 that represented Intel’s second generation of Core processors. It has 4 cores and 8 threads, with a base clock of 2.10 GHz and a boost clock of 3.00 GHz. The process node difference is significant: 14 nm versus 32 nm. This means the G5400’s transistors are substantially smaller, allowing for higher clock speeds and better power efficiency per unit of work. The die size reflects this, with the G5400 at 126 mm² compared to the i7-2710QE’s 216 mm². The i7-2710QE also lists 1,160 million transistors, while the G5400 does not have a transistor count in the data.

Cache configurations also differ. Both have 64 KB of L1 cache per core and 256 KB of L2 cache per core. However, the L3 cache is different: the G5400 has 4 MB shared, while the i7-2710QE has 6 MB shared. That additional 2 MB of L3 cache on the i7-2710QE likely helps it compensate for its lower clock speeds in some workloads, though the benchmark data does not show a significant overall advantage. The integrated graphics differ as well, with the G5400 using UHD Graphics 610 and the i7-2710QE using Intel HD 3000. The memory support also diverges: the G5400 supports DDR4 with a dual-channel bus and a memory bandwidth of 38.4 GB/s, while the i7-2710QE has no listed memory support type or bandwidth, though it does use a dual-channel bus. The G5400 also has PCIe Gen 3 with 16 lanes from the CPU, while the i7-2710QE has no PCIe specification listed. Both processors have locked multipliers, so neither can be overclocked.

Specification Differences

Several specification fields differ between the two processors, and these differences are important for platform compatibility. The most obvious is the socket: the G5400 uses Intel Socket 1151, while the i7-2710QE uses Intel Socket G2 (988B). These are not interchangeable, meaning the choice of processor dictates the motherboard. The market segment also differs, with the G5400 classified as Desktop and the i7-2710QE as Mobile. The core and thread counts differ as noted: 2 cores and 4 threads versus 4 cores and 8 threads. The base clock differs significantly, with the G5400 at 3.70 GHz versus the i7-2710QE’s 2.10 GHz, and the i7-2710QE has a boost clock of 3.00 GHz that the G5400 lacks entirely. The TDP also differs, with the G5400 at 58 watts and the i7-2710QE at 45 watts, making the mobile chip more power-efficient despite its older architecture.

The process node is a major difference: 14 nm for the G5400 versus 32 nm for the i7-2710QE. The die size is also different, at 126 mm² versus 216 mm². The transistor count is only listed for the i7-2710QE at 1,160 million, with no figure for the G5400. L3 cache differs, with 4 MB on the G5400 versus 6 MB on the i7-2710QE. Memory support is another field where they differ: the G5400 lists DDR4, while the i7-2710QE has no memory support type listed. The memory bandwidth is listed only for the G5400 at 38.4 GB/s. PCIe support is listed only for the G5400, as Gen 3 with 16 lanes. The integrated graphics differ, with UHD Graphics 610 versus Intel HD 3000. The release dates are far apart, with the G5400 in April 2018 and the i7-2710QE in January 2011. The launch MSRP is $64 for the G5400, while the i7-2710QE has no listed MSRP. The part numbers also differ: SR3X9 for the G5400 and SR02T for the i7-2710QE. Both are end-of-life and have locked multipliers.

FAQ

Q: Which processor is faster in single-core performance?

A: The Intel Core i7-2710QE wins in both single-core tests. It scores 188 in Cinebench R20 single-core versus 187 for the G5400, and 449 versus 447 in Cinebench R23 single-core. The margins are 0.5% and 0.4% respectively.

Q: Does the G5400 have any benchmark where it wins?

A: No. The head-to-head data shows the i7-2710QE winning all five recorded benchmarks, with the G5400’s best relative result being a 0.4% deficit in Cinebench R23 single-core.

Q: How do the core counts affect the benchmark results?

A: The i7-2710QE has 4 cores and 8 threads, double the G5400’s 2 cores and 4 threads. Despite this, the G5400’s higher base clock of 3.70 GHz versus 2.10 GHz nearly cancels out the core advantage, resulting in a maximum multicore delta of just 0.6% in Cinebench R15.

Q: What are the power consumption differences?

A: The G5400 has a TDP of 58 watts, while the i7-2710QE has a TDP of 45 watts. This makes the older mobile chip more power-efficient, despite its larger 32 nm process node versus the G5400’s 14 nm node.

Q: Can these processors be used on the same motherboard?

A: No. The G5400 uses Intel Socket 1151, while the i7-2710QE uses Intel Socket G2 (988B). They are incompatible with each other’s platforms.

Q: Which processor has more L3 cache?

A: The i7-2710QE has 6 MB of shared L3 cache, while the G5400 has 4 MB of shared L3 cache. The i7-2710QE also has the same per-core L1 and L2 cache sizes as the G5400.

DETAILED SPECIFICATIONS

SPECIFICATION
i7-2710QE
Pentium Gold G5400
Core Specs
Cores
4
2 -50.0%
Threads
8
4 -50.0%
Base Clock (GHz)
2.1
3.7 +76.2%
Boost Clock (GHz)
3
—
Frequency (GHz)
2.1
3.7 +76.2%
Turbo Clock (GHz)
3
—
Multiplier
21
37 +76.2%
SMP CPUs
1
1 0.0%
Cache
L1 Cache
64 KB (per core)
64 KB (per core)
L2 Cache
256 KB (per core)
256 KB (per core)
L3 Cache
6 MB (shared)
4 MB (shared)
Power
TDP (W)
45
58 +28.9%
Architecture
Architecture
Sandy Bridge
Coffee Lake
Codename
Sandy Bridge
Coffee Lake
Generation
Core i7 (Sandy Bridge)
Pentium Gold (Coffee Lake)
Process Size
32 nm
14 nm
Transistors
1,160 million
—
Die Size
216 mm²
126 mm²
Foundry
Intel
Intel
Memory
Memory Support
—
DDR4
Memory Bus
Dual-channel
Dual-channel
Memory Bandwidth
—
38.4 GB/s
ECC Memory
No
No
Platform
Socket
Intel Socket G2 (988B)
Intel Socket 1151
PCIe
—
Gen 3, 16 Lanes(CPU only)
Graphics
Integrated Graphics
Intel HD 3000
UHD Graphics 610
Other
Market
Mobile
Desktop
Production Status
End-of-life
End-of-life
Launch Price
—
$64
Part Number
SR02T
SR3X9
Package
rPGA
FC-LGA1151
Tj Max
—
100°C
View Core i7-2710QE Details View Pentium Gold G5400 Details